OSHA - OSHA Certified Crane Operator Practice Test

โ–ถ

Anyone searching for the OSHA crane and rigging standard usually wants one thing: a clear answer about what the law requires before a lift happens. Many people also begin with an OSHA establishment search, the public tool that shows inspection histories, citations, and penalties for a specific employer or job site. Together, the rules and the enforcement record tell a complete story. This guide explains the federal crane and rigging requirements, how inspectors apply them, and how crews can stay compliant.

Anyone searching for the OSHA crane and rigging standard usually wants one thing: a clear answer about what the law requires before a lift happens. Many people also begin with an OSHA establishment search, the public tool that shows inspection histories, citations, and penalties for a specific employer or job site. Together, the rules and the enforcement record tell a complete story. This guide explains the federal crane and rigging requirements, how inspectors apply them, and how crews can stay compliant. Practice with the free OSHA - OSHA Certified Crane Operator practice test on PracticeTestGeeks (21 questions with answer explanations).

Crane work is regulated more tightly than most construction tasks because the consequences of a mistake are severe. A single failed lift can drop thousands of pounds onto workers below, tip a machine, or energize a power line. The construction crane rule, 29 CFR 1926 Subpart CC, took effect in 2010 and replaced a patchwork of older consensus standards. OSHA estimated at the time that the rule would prevent about 22 deaths and 175 injuries every year.

Rigging sits beside crane operation in the regulations, and it deserves equal attention. Slings, shackles, hooks, spreader bars, and hardware must be rated for the load, inspected before use, and removed from service when damaged. General rigging rules appear in 1926.251, while Subpart CC adds requirements for qualified riggers during assembly, disassembly, and hoisting. A crane operating perfectly can still cause an accident if a sling is overloaded, a hitch is wrong, or the load is unbalanced.

The two sets of rules cover different workplaces. Subpart CC governs power-operated equipment used in construction that can hoist, lower, and horizontally move a suspended load, including mobile, tower, crawler, and derrick cranes. Overhead and gantry cranes in factories and warehouses fall under general industry rules, mainly 1910.179, while mobile cranes in general industry follow 1910.180. Knowing which part applies to your site matters, because inspection intervals, certification duties, and documentation differ between construction and general industry employers.

Employers are the main duty holders. They must make sure operators are trained, certified or qualified, and evaluated, that equipment is inspected on schedule, that ground conditions can support the machine, and that every lift follows the manufacturer's load chart. Workers also carry responsibility. Operators must refuse to lift when they believe safety is compromised, and signal persons must understand the signals they use. Safety is shared across the crew, and the regulations assign specific tasks to each role.

This article is awareness content, not legal advice, but it gives you a practical map. You will find the key sections of Subpart CC, statistics worth remembering, a checklist you can use on site, and the pros and cons of the current framework. You will also learn how to read a contractor's inspection history through an OSHA establishment search. Related site-safety duties, such as guardrails around the same work areas, are covered in our guide that complements these osha crane safety regulations.

Finally, remember that regulations change and states may add requirements. More than twenty states run their own OSHA-approved State Plans, and some, such as California, maintain crane rules that differ from the federal text. Employers should always confirm the current wording at osha.gov and check state rules before starting work. If you are preparing for a certification exam, treat the federal text as your baseline and then learn local variations.

OSHA: upcoming dates and official changes
  • Updated Nov 10, 2026: Delivery is now Written: online proctored (OPT), test center (TCT) or Event Online Testing (EOT); Practical: hands-on with a CCO Practical Proctor (previously Written: online proctored, test center, or event online testing; practical: hands-on crane exam).
  • Updated Nov 10, 2026: Eligibility is now Age 18+; comply with CCO Substance Abuse Policy and Code of Ethics; pass written and practical exams (either order) (previously Age 18+; pass Core + one Specialty written and a Practical exam within 12 months).
  • Updated Nov 10, 2026: Number of questions (Core written exam) is now 95 multiple-choice questions (previously 95 multiple-choice questions).

Facts verified Nov 10, 2026 against CCO. Dates that have passed are removed automatically.

  • The CCO Mobile Crane Operator Core written exam has 95 multiple-choice questions. (CCO)
  • The CCO Mobile Crane Operator Core written exam has a 90-minute time limit. (CCO)
  • The CCO Mobile Crane Operator Core written exam costs $140. (CCO)
  • The CCO Mobile Crane Operator practical exam costs $70 per exam, and the practical proctor may charge separate fees. (CCO)
  • The CCO Mobile Crane Operator certification is valid for 5 years. (CCO)
  • Under OSHA 29 CFR 1926.1427, a crane operator certification issued by an accredited testing organization is valid for 5 years. (osha.gov)
  • Most CCO certifications are valid for five years and require a written exam to recertify, and recertification can begin up to 12 months before expiry. (CCO)
  • The CCO Mobile Crane Operator written exam can be taken by online proctored testing, at a test center, or at an Event Online Testing site, and the practical exam is administered by a CCO-credentialed Practical Proctor. (CCO)
  • To earn the CCO Mobile Crane Operator certification, candidates must be at least 18 years old and comply with CCO's Substance Abuse Policy and Code of Ethics. (CCO)

Facts verified Nov 10, 2026 against CCO. Dates that have passed are removed automatically.

OSHA Exam at a Glance

ItemDetailOfficial source
Number of questions (Core written exam)95 multiple-choice questionsCCO
Time limit (Core written exam)90 minutesCCO
Exam fee (Core written exam)$140CCO
Exam fee (Practical exam)$70 per practical (proctor may charge separate fees)CCO
Exam fee (Specialty written exam)$80 per SpecialtyCCO
Validity5 yearsCCO
Validity (OSHA regulation)OSHA: accredited-organization certification valid 5 yearsosha.gov
RenewalBegin recertification up to 12 months before expiry; written exam requiredCCO
DeliveryWritten: online proctored (OPT), test center (TCT) or Event Online Testing (EOT); Practical: hands-on with a CCO Practical ProctorCCO
EligibilityAge 18+; comply with CCO Substance Abuse Policy and Code of Ethics; pass written and practical exams (either order)CCO
Score releasePreliminary results shown on screen immediately after finishingCCO

Facts verified Nov 10, 2026 against CCO. Dates that have passed are removed automatically.

Free OSHA - OSHA Certified Crane Operator Study Tools

Interactive OSHA - OSHA Certified Crane Operator resources on PracticeTestGeeks, free to start:

OSHA Crane Regulations by the Numbers

๐Ÿ“…
2010
Subpart CC Took Effect
๐Ÿ›ก๏ธ
22
Deaths Prevented Yearly
๐ŸŽ“
5 yrs
Operator Certification Validity
โš ๏ธ
20 ft
Minimum Power Line Clearance
๐Ÿ“‹
12 mo
Annual Inspection Record Retention
Test Your OSHA Crane and Rigging Standard Knowledge

Core Parts of the OSHA Crane and Rigging Standard

๐Ÿ—๏ธ Subpart CC (Construction)

Sections 1926.1400 through 1926.1442 cover cranes and derricks in construction, including assembly, inspection, operator qualification, signals, power line safety, and hoisting personnel. Most contractors working with mobile or tower cranes must follow this subpart.

๐Ÿญ General Industry Cranes

Sections 1910.179 and 1910.180 address overhead, gantry, crawler, locomotive, and truck cranes in factories, warehouses, and plants. They set inspection frequencies, rated load marking, and operating rules for non-construction workplaces.

๐Ÿชข Rigging Equipment Rules

Section 1926.251 and 1910.184 govern slings, hardware, and rigging for material handling. They require rated capacity tags, pre-use inspection, and removal of damaged gear, so the connection between crane and load is as safe as the crane.

๐ŸŽ“ Operator and Signal Person Qualification

Operators must be certified or qualified and evaluated by the employer, while signal persons need documented qualification. Sections 1926.1427 and 1926.1428 spell out the accepted routes, records, and renewal periods for each role.

โšก Power Line and Ground Safety

Employers must assess ground conditions and keep equipment clear of energized lines. Sections 1926.1402 and 1926.1407 through 1926.1411 give the compliance options, minimum clearances, and planning steps that prevent tip-overs and electrocutions.

Key Requirements of the OSHA Crane and Rigging Standard in Subpart CC

Subpart CC is organized around the life of a lift. It starts with ground conditions and assembly, moves through inspections, operation, and signals, and ends with disassembly. Section 1926.1402 requires the controlling entity to ensure the ground is firm, drained, and graded enough to support the crane and its supporting materials. Soft soil, buried utilities, and recent excavation are common causes of tip-overs, so a documented ground check before setup is one of the cheapest safeguards available.

Inspection duties come in layers. A competent person must visually inspect the crane before each shift, looking for leaks, damaged controls, and obvious wear. Monthly inspections, documented and signed, cover items such as wire rope and critical components, with records kept for three months. An annual inspection by a qualified person is also required, with records retained for 12 months. Any deficiency that could affect safe operation must be corrected before the crane returns to service.

Wire rope receives special scrutiny under 1926.1413. Running rope must be removed from service when it shows six randomly distributed broken wires in one rope lay, or three broken wires in one strand within one lay, along with severe corrosion, kinking, crushing, or heat damage. The competent person checks running ropes at the start of each shift and keeps a monthly record. Because a failed hoist rope can drop a load instantly, many contractors replace rope earlier than the minimum criteria require.

Operator qualification is covered by 1926.1427. Since the 2018 final rule, employers must ensure operators are certified by an accredited testing organization by crane type, or by type and capacity, or qualified through an audited employer program, the military, or a government license. Certification lasts five years. Crucially, the rule also requires the employer to evaluate each operator's ability to run the specific machine and document that evaluation. A certification card alone is not enough.

Signal persons are covered by 1926.1428. When the operator cannot see the load or landing area, or the crane's movement is not clear, a qualified signal person must be used. Qualification requires a documented assessment, by a third party or the employer, showing the person knows the standard hand signals, understands any radio or voice signals used, and can recognize crane hazards. Hand signals follow Appendix A of Subpart CC, so crews should not improvise their own gestures.

Power line safety is among the most heavily cited areas. Sections 1926.1407 through 1926.1411 require the employer to identify the work zone, determine whether any part of the crane or load could come within 20 feet of an energized line, and then choose a compliance option. For lines above 350 kV the clearance grows to 50 feet. Options include de-energizing and grounding the line, maintaining the required clearance, or using the table of minimum approach distances with a planned procedure.

Load charts and capacity limits tie everything together. The operator must have the manufacturer's load chart available and may not exceed rated capacity for the configuration in use, including boom length, radius, outrigger setup, and deductions for hook blocks, jibs, or rigging weight. Before each lift, someone must know the load weight. Estimating by eye is a frequent root cause of overloads, which is why scales, load cells, and engineered lift plans are common on critical picks.

Free OSHA Crane Operation Controls & Signal Communication Questions and Answers
Practice hand signals, control functions, and communication rules that operators and signal persons need for safe lifts.
Free OSHA Crane Safety Procedures & Hazard Prevention Questions and Answers
Test your knowledge of power line clearances, ground conditions, and hazard prevention procedures used on crane sites.

OSHA Establishment Search: Reading Enforcement Data for Cranes

๐Ÿ“‹ How the Search Works

The OSHA establishment search is a free public database on osha.gov that lists federal inspections by employer name, site address, state, inspection type, and date range. Enter a contractor or crane company name, narrow the results by year or industry code, and the tool returns each inspection with an activity number, opening date, and current status. Opening an individual record reveals the citations, the standards cited, proposed penalties, and whether the case was contested or settled.

State Plan inspections may not appear in the same federal database, so results can be incomplete for employers in states such as California or Washington. Names also vary: a company may be listed under a parent name, a subsidiary, or a misspelling. Try several variations and search by city as well. A blank result does not prove a clean record, only that no federal inspection matched the search terms you entered.

๐Ÿ“‹ Interpreting Crane Citations

Crane citations usually reference the 1926.1400 series. Frequent ones include 1926.1404 for assembly and disassembly procedures, 1926.1408 for power line clearance, 1926.1412 for inspections, 1926.1417 for operations, and 1926.1427 for operator qualification. Each citation is classified as other-than-serious, serious, repeat, or willful. A serious classification means a substantial probability of death or serious physical harm, while willful means the employer knew about the hazard or showed plain indifference.

Penalty amounts and abatement dates matter too. Maximum federal penalties are adjusted annually for inflation and in recent years have exceeded $16,000 for a serious violation and $165,000 for a willful or repeat violation. Check whether the employer contested the citation, which can signal a dispute over the facts, and whether a settlement lowered the classification. Patterns across several inspections reveal more about how seriously a company treats lifting operations than one isolated citation.

๐Ÿ“‹ Using Results for Safety Planning

General contractors and project owners can use an OSHA establishment search during subcontractor prequalification. Look for repeat citations under the crane standard, fatality investigations, and unresolved abatement. Pair the results with a request for the company's crane inspection records, operator certifications, and lift planning procedures. A subcontractor with strong paperwork and a clean enforcement history is far less likely to create liability for the controlling employer on a shared site.

Workers and job seekers can use the same tool to evaluate a prospective employer before accepting a crane operator, rigger, or signal person role. Operators studying for certification can also read real citation narratives to see how the rules apply in practice. Case summaries often describe the exact sequence of errors, such as a missing load chart or an unqualified signal person, which makes the abstract regulations easier to remember during an exam.

Does the Federal Crane Standard Help or Hinder Contractors?

Pros

  • Sets one nationwide baseline for crane inspection, operation, and documentation.
  • Requires operator certification and employer evaluation, raising skill levels across the industry.
  • Clear power line rules reduce electrocutions, a leading cause of crane deaths.
  • Qualified signal person and rigger requirements improve communication on busy sites.
  • Public enforcement data lets owners compare contractors before awarding work.
  • Documented inspections help employers defend themselves after an incident or audit.

Cons

  • Recordkeeping for shift, monthly, and annual inspections adds administrative time.
  • Certification and evaluation costs can burden small contractors and rental firms.
  • Different rules for construction and general industry confuse mixed-use employers.
  • State Plans can add stricter requirements that complicate multi-state projects.
  • Multi-employer responsibility means one subcontractor's mistake can create liability for others.
  • Frequent updates and interpretation letters require ongoing training for safety managers.

Pros and Cons at a Glance

ProsCons
Sets one nationwide baseline for crane inspection, operation, and documentation.Recordkeeping for shift, monthly, and annual inspections adds administrative time.
Requires operator certification and employer evaluation, raising skill levels across the industry.Certification and evaluation costs can burden small contractors and rental firms.
Clear power line rules reduce electrocutions, a leading cause of crane deaths.Different rules for construction and general industry confuse mixed-use employers.
Qualified signal person and rigger requirements improve communication on busy sites.State Plans can add stricter requirements that complicate multi-state projects.
Public enforcement data lets owners compare contractors before awarding work.Multi-employer responsibility means one subcontractor's mistake can create liability for others.
Documented inspections help employers defend themselves after an incident or audit.Frequent updates and interpretation letters require ongoing training for safety managers.
Free OSHA Load Handling & Rigging Techniques Questions and Answers
Review sling angles, hitch types, load weight calculations, and safe rigging practices for crane lifts.
Free OSHA Regulations & Equipment Inspection Standards Questions and Answers
Check your understanding of inspection frequencies, wire rope criteria, and recordkeeping duties under federal standards.

Site Checklist for the OSHA Crane and Rigging Standard

Verify ground conditions and document the check before setup.
Confirm every operator holds current certification and an employer evaluation.
Complete and record the shift inspection before the first lift.
File monthly and annual inspection records where inspectors can find them.
Keep the manufacturer's load chart available at the operator's station.
Identify all energized lines and select a power line compliance option.
Assign a qualified signal person whenever the operator's view is blocked.
Inspect slings, shackles, and hooks before each use and remove damaged gear.
Confirm the load weight and sling angles before attaching the load.
Barricade the swing radius and keep workers out from under suspended loads.
Certification Is Not the Same as Qualification to Operate Your Crane

Passing a certification exam does not end the employer's duty. Under 1926.1427, employers must also evaluate that the operator can safely run the specific machine on their site and document the result. Inspectors ask for both records, so keep them together.

How OSHA Enforces Crane and Rigging Rules on the Job Site

OSHA inspections do not happen at random only. Federal compliance officers prioritize imminent danger situations, fatalities and catastrophes, worker complaints, referrals from other agencies, and programmed inspections targeting high-hazard industries such as construction. A crane collapse that injures workers or draws public attention almost always triggers an inspection. Employers must report a work-related death within eight hours, and an inpatient hospitalization, amputation, or loss of an eye within 24 hours, so incidents rarely go unnoticed.

When an inspector arrives, the process follows a predictable pattern. The compliance officer presents credentials, holds an opening conference, walks the site, interviews employees, and reviews documents. For crane operations they commonly request inspection records, operator certifications, the employer's evaluation of each operator, signal person qualification documents, load charts, assembly and disassembly procedures, and rigging inspection logs. Missing paperwork is often easier to cite than a hazard, so organized records are a real defense.

Construction sites usually involve several employers, and OSHA's multi-employer citation policy allows more than one to be cited for the same hazard. The creating employer introduced the hazard, the exposing employer had workers exposed to it, the correcting employer was responsible for fixing it, and the controlling employer had general supervisory authority over the site. A general contractor can therefore be cited for a subcontractor's crane violation if it failed to exercise reasonable care to prevent or detect it.

Subpart CC adds explicit duties for the controlling entity, particularly regarding ground conditions and underground hazards. If the crane user needs information about buried utilities, voids, or fill, the controlling entity must provide what it knows or can reasonably obtain. This allocation of responsibility means that communication between the crane company and the site owner is not optional. Written pre-lift meetings, shared site plans, and signed ground condition acknowledgments help show that each party met its obligations.

Penalties scale with the seriousness of the violation. Federal maximums are adjusted annually and currently exceed $16,000 per serious or other-than-serious violation and exceed $165,000 for each willful or repeat violation. Inspectors also assign an abatement period, and failure to abate can bring daily penalties. Employers have 15 working days after receiving a citation to contest it or request an informal conference, so deadlines should be tracked carefully and never ignored.

Results of these inspections eventually become public, which is where an OSHA establishment search becomes useful. After a case closes or advances, the activity number, standards cited, and penalties appear in the database. Insurers, owners, unions, and journalists all use that data. A single serious crane citation can affect bonding, prequalification scores, and bidding opportunities for years, so the reputational cost often exceeds the fine itself, which is another reason to prevent violations before they occur.

Employees also have rights that support enforcement. They can file a complaint, request an inspection, speak privately with compliance officers, and refuse work in rare cases of imminent danger where a reasonable person would believe death or serious injury is likely. Retaliation for exercising these rights is prohibited under Section 11(c) of the OSH Act, and complaints must be filed within 30 days. Operators who stop a questionable lift are protected by this framework and by the regulations themselves.

Rigging Hardware, Slings, and Load Handling Under the OSHA Crane and Rigging Standard

Rigging failures are usually preventable, and the regulations focus on simple discipline. Every sling must carry a legible tag or marking showing its rated capacity for the hitch type used, and that rating must never be exceeded. Slings must be inspected before each shift, and again whenever conditions change. Frayed webbing, broken wires, stretched chain links, heat damage, or distorted fittings require removal from service. Damaged slings should be tagged and destroyed or repaired by a qualified person, not left on the rack.

Sling angle is the concept most often tested and most often misjudged. When a sling leg is angled away from vertical, tension in each leg increases. Consider a 2,000-pound load lifted with a two-leg bridle. At 60 degrees from horizontal each leg carries about 1,155 pounds, but at 30 degrees from horizontal each leg carries 2,000 pounds. Riggers should avoid angles below 45 degrees whenever possible, and they must use the lower rated capacity that matches the actual angle.

Hitch type changes capacity as well. A vertical hitch, a choker hitch, and a basket hitch each have different rated values, and a choker hitch typically reduces a sling's capacity to roughly 75 to 80 percent of its vertical rating, depending on the sling material and angle. Riggers must also protect slings from sharp edges using corner protectors, avoid knots, never shorten slings with bolts or makeshift devices, and never shock load. Sudden jerks can multiply forces well beyond the static weight.

Hooks and hardware demand equal care. Hooks should have working safety latches unless a qualified person determines that a latch would create a greater hazard, and hook throats that have opened or twisted beyond manufacturer limits must be replaced. Shackles must be the correct size with the pin fully seated, and hardware must match the working load limit stamped on the body. Below-the-hook lifting devices such as spreader bars and vacuum lifters should have marked capacities and documented inspections.

Load control begins before the hook moves. The qualified rigger confirms the weight, finds the center of gravity, selects the sling arrangement, and attaches the load so it will rise level. A test lift of a few inches lets the crew check balance, brake performance, and hitch security. Tag lines, used when needed, keep the load from rotating without placing workers in the line of fire. Workers must never ride the load or the hook, and nobody may stand under a suspended load.

Hoisting personnel is allowed only in limited cases. Under 1926.1431, employers must show that using a crane or derrick to hoist workers is necessary because conventional means, such as a scaffold or aerial lift, would be more hazardous or impossible. When allowed, strict requirements apply, including a personnel platform designed by a qualified person, proof testing, a trial lift, and a pre-lift meeting. These requirements are demanding on purpose, and shortcuts here are some of the most severe violations OSHA cites.

Documentation and training close the loop. Qualified riggers, defined in the standard as people with a recognized degree, certificate, or extensive knowledge and experience who can solve rigging problems, are required for assembly and disassembly rigging and for hooking up loads when the weight, balance, or configuration creates a hazard. Employers should keep training records, inspection logs, and manufacturer instructions together, because inspectors often evaluate rigging compliance through the paper trail left after the lift.

Practice Crane Hazard Prevention Questions

Practical Tips for Mastering Crane Safety Regulations

Start your preparation by learning how the regulations are organized instead of memorizing isolated rules. Subpart CC follows the sequence of a project: ground conditions, assembly, inspection, operator qualification, operation, signals, power lines, and disassembly. When you can place a question in that sequence, the answer becomes easier to reason out. Make a one-page outline with section numbers, and review it daily for a week until each topic feels familiar and connected to the next.

Memorize the numbers that appear repeatedly. Five years for operator certification, three months for monthly inspection records, twelve months for annual records, twenty feet for power line clearance, fifty feet above 350 kV, and six broken wires in one rope lay for running rope removal. Write them on flashcards and quiz yourself in the car or at lunch. Many exam questions test these figures directly, and real inspectors expect safety personnel to know them without checking.

Use practice questions strategically. Take a short quiz on one topic, read every explanation, and note why wrong answers were wrong. Then retake the set after a day. Mixing topics later builds the flexibility you need on a real exam. Our free quizzes on signal communication, hazard prevention, rigging, and inspection standards are organized by topic, so you can target weak areas rather than repeating material you already understand.

Get hands-on exposure whenever you can. Ask a rigger to show you how sling tags look, how a shackle pin seats, and how a competent person completes a shift inspection. Watch an experienced signal person direct a lift and compare their hand signals with Appendix A. Practical memory complements written study, and it helps you spot the details exam writers love, such as a missing latch, a worn tag, or an operator who cannot see the load.

Read real enforcement cases. An OSHA establishment search for crane contractors will show citations that describe how violations actually happen. You might find an inspector citing a company for failing to document the operator evaluation, or for placing a crane within the power line clearance zone. Reading three or four of these summaries turns abstract rules into memorable stories, and they teach you how auditors think when they walk onto a site.

Build habits that mirror compliance on the job. Keep a simple binder or digital folder with certifications, evaluations, inspection logs, and lift plans. Practice a pre-lift meeting script covering load weight, rigging, route, signals, and stopping conditions. Teach another person a concept in your own words; if you can explain sling angle or the power line options clearly, you probably understand them. Consistent habits protect you on the exam and, more importantly, on the site.

Finally, stay current. Review OSHA's crane and derrick page, read any new interpretation letters, and check your state's rules before each new project. If you hold certification, calendar your renewal date well before the five-year mark. Take a final timed practice test a few days before your exam, rest the night before, and read each question carefully. Careful reading, steady habits, and respect for the regulations will serve you throughout a crane career.

OSHA Code Compliance
Assess your grasp of federal code requirements, citations, and employer compliance duties in a timed practice test.
OSHA Crane Operator Certification & Qualification Requirements 1
Practice questions on operator certification routes, employer evaluation, renewal periods, and qualification documentation rules.

Sample OSHA - OSHA Certified Crane Operator Practice Questions

Try these questions from our free OSHA - OSHA Certified Crane Operator practice tests. The correct answer and an explanation follow each question.

  1. Which OSHA standard governs crane and derrick operations in construction, including power line safety requirements?

    • A. 29 CFR 1926.502
    • B. 29 CFR 1926.1400 (Subpart CC)
    • C. 29 CFR 1910.179
    • D. 29 CFR 1926.550

    Answer: B. 29 CFR 1926.1400 (Subpart CC)

    29 CFR 1926.1400 (Subpart CC), effective 2010, is the comprehensive OSHA standard governing cranes and derricks in construction including electrical hazard requirements.

  2. What is the most critical safety requirement in environmental standards?

    • A. Speed of completion
    • B. Following all applicable safety regulations and wearing required PPE
    • C. Cost minimization
    • D. Working alone to avoid delays

    Answer: B. Following all applicable safety regulations and wearing required PPE

    Safety regulations and proper PPE use are the most critical requirements in environmental standards to prevent injury and ensure compliance.

  3. What is the OSHA regulation number that governs crane safety?

    • A. 29 CFR 1910 Subpart D
    • B. 29 CFR 1926 Subpart CC
    • C. 29 CFR 1904 Subpart E
    • D. 29 CFR 1930 Subpart A

    Answer: B. 29 CFR 1926 Subpart CC

    OSHA's regulations for cranes and derricks in construction are specifically found under 29 CFR 1926 Subpart CC. This subpart outlines comprehensive safety requirements for the operation, inspection, maintenance, and training related to cranes on construction sites. Adherence to this specific regulation is mandatory for ensuring crane safety.

  4. How does OSHA enforce crane safety regulations?

    • A. Voluntary surveys
    • B. Certification giveaways
    • C. Site inspections and citations
    • D. Phone surveys

    Answer: C. Site inspections and citations

    OSHA enforces its safety regulations primarily through unannounced site inspections conducted by compliance officers. If violations are found during these inspections, OSHA issues citations and proposes penalties to employers. This enforcement mechanism ensures that employers comply with safety standards, including those for crane operations, thereby protecting workers.

Take the full OSHA - OSHA Certified Crane Operator practice test

OSHA Questions and Answers

What is the OSHA crane and rigging standard?

It is a group of federal rules rather than a single document. For construction, 29 CFR 1926 Subpart CC covers cranes and derricks, while 1926.251 covers rigging equipment. General industry employers follow 1910.179, 1910.180, and 1910.184. Together they address inspections, operator qualification, signals, power lines, load capacity, and sling and hardware safety.

What is an OSHA establishment search?

It is a free online tool on osha.gov that lets you look up federal inspections by employer name, location, date, and other filters. Each result shows the inspection type, standards cited, penalties, and case status. People use it to evaluate contractors, research incidents, and study how crane and rigging rules are enforced.

How long is crane operator certification valid under OSHA?

Under 1926.1427, certification issued by an accredited testing organization is valid for five years. Employers must still evaluate each operator on the specific equipment they will run and document that evaluation. Operators should schedule renewal before expiration, since working with an expired certification can lead to citations for both employer and operator.

How close can a crane get to power lines?

For lines rated up to 350 kV, the standard requires keeping the crane, load line, and load at least 20 feet away unless the line is de-energized and grounded or another compliance option is used. For lines above 350 kV, the minimum clearance is 50 feet. Employers must plan these lifts before work starts.

How often must a crane be inspected?

Subpart CC requires a competent person to inspect before each shift, with documented monthly inspections kept for three months. A qualified person must complete an annual inspection, with records kept for 12 months. Wire rope has its own shift and monthly requirements. Any deficiency affecting safe operation must be fixed before the crane returns to service.

When must a signal person be used?

A qualified signal person is required when the point of operation is not in the operator's full view, when the operator's view of the travel path is obstructed, or when site conditions make the crane's movement unclear. The signal person must be assessed and documented as knowing the standard signals and recognizing crane hazards.

What wire rope damage requires removal from service?

For running wire rope, removal is required with six randomly distributed broken wires in one rope lay or three broken wires in one strand in one lay. Severe corrosion, kinking, crushing, bird-caging, and heat damage also require removal. Rotation-resistant rope has stricter limits, so check the exact criteria in 1926.1413 and the manufacturer's instructions.

Who is responsible for crane safety on a multi-employer site?

Several parties share responsibility. The crane employer must meet operator, inspection, and operation requirements, while the controlling entity must address ground conditions and share information about site hazards. OSHA's multi-employer policy allows the creating, exposing, correcting, and controlling employers to be cited when each fails its role.

What penalties can employers face for crane violations?

Federal penalties are adjusted yearly for inflation. In recent years the maximum has exceeded $16,000 per serious violation and $165,000 per willful or repeat violation. Failure to abate can add daily penalties. Employers have 15 working days after receiving a citation to contest it or request an informal conference.

Do state plans change the crane rules?

Yes, they can. More than twenty states operate OSHA-approved State Plans that must be at least as effective as federal rules, and some add stricter requirements such as operator licensing. Employers working in those states should consult the state agency, because federal databases may not show state-level inspections or citations.

How many questions are on the OSHA?

The CCO Mobile Crane Operator Core written exam has 95 multiple-choice questions. (Verified Nov 10, 2026 against CCO.)

How much does the OSHA cost?

The CCO Mobile Crane Operator Core written exam costs $140. (Verified Nov 10, 2026 against CCO.)
โ–ถ Start Quiz