Forklift Tires: A Complete Guide to Types, Wear and Safe Operation for TLILIC0003 Candidates in Australia
๐ฏ Forklift tires explained for Australian operators: cushion, pneumatic and solid types, daily checks, wear limits and what TLILIC0003 expects of you.

Forklift tires are the only part of a forklift that actually touches the warehouse floor, yet they rarely get the attention that forks, mast chains or hydraulics receive. Every kilogram of load, every turn and every emergency stop passes through those patches of rubber or polyurethane. For anyone preparing for the TLILIC0003 licence in Australia, understanding forklift tires is part of understanding stability, traction and safe operation. Practice with the free Forklift Licence practice test on PracticeTestGeeks (300+ questions with answer explanations).
Australian workplaces run forklifts on very different surfaces. A food distribution centre in Western Sydney might have polished concrete and chilled docks, while a timber yard near Mackay has gravel, mud and ramps. A single tire design cannot suit both. That is why manufacturers offer cushion, pneumatic and solid pneumatic options, and why a competent operator can look at a truck and quickly judge whether its tires match the job in front of them.
Tire condition also links directly to the duty of care under the Work Health and Safety laws that apply across most Australian states and territories. A person conducting a business or undertaking must keep plant in a safe condition, and operators must report defects they notice. Worn, damaged or incorrectly inflated tires reduce the stability of a truck, lengthen stopping distances and make steering unpredictable. Those are exactly the hazards that lead to tip-overs, dropped loads and pedestrian collisions.
The TLILIC0003 unit, Licence to operate a forklift truck, expects candidates to complete pre-operational checks and identify faults before work starts. Tires are on that list alongside forks, chains, brakes, steering, horn, lights and the operator restraint system. During practical assessment you may be asked to walk around a truck and explain what you are looking for. Being able to describe wear lines, cuts, chunking and pressure shows the assessor you understand why each check matters.
This article is awareness content rather than a maintenance manual. It will not replace the manufacturer's handbook for your specific truck, and it cannot tell you the exact pressure for a particular pneumatic tire. What it can do is give you a practical framework: know the types, know the surfaces they suit, know the warning signs of wear, and know when to stop work and report. That framework is useful on the exam and on the shop floor.
You will also find a quick set of numbers, a step-by-step inspection routine, a comparison of the main tire types, a checklist you can use for your own pre-start routine, and answers to questions that new operators commonly ask. If you are still working towards your licence, the practice tests linked throughout this page help you rehearse the attachments, modifications and equipment questions that often catch candidates out. Use them alongside the guide, not instead of it.
A final point before we dive in: in Australian workplaces and on most supplier websites you will often see the word tyres spelled the local way. We use forklift tires in this guide because it matches how many people search, but the equipment, the standards and the safety logic are identical. Whichever spelling you use, the message is the same. Look at the tires every shift, never ignore a defect, and never operate a truck you consider unsafe.
Free Forklift Licence Study Tools
Interactive Forklift Licence resources on PracticeTestGeeks, free to start:
- Forklift Licence practice test โ 300+ questions with instant scoring and answer explanations
- Forklift Licence flashcards โ review key terms and concepts card by card
- Forklift Licence study guide โ topic-by-topic overview of what the exam covers
- Forklift Licence cheat sheet โ one-page printable summary for last-minute review
Forklift Tires by the Numbers

How to Inspect Forklift Tires Before Every Shift
Park Safely and Switch Off
Walk Around and Look
Check Wear Lines and Tread
Check Pressure and Valves
Record and Report Defects
Cushion tires are the most familiar choice for indoor trucks. They consist of a solid rubber ring pressed onto a steel band, giving a smooth, treadless surface that sits low to the ground. Because the profile is compact, cushion-tire trucks have a tight turning radius, which suits narrow aisles in warehouses and retail stores. The trade-off is limited tolerance for rough ground. Cracks, debris and wet concrete reduce grip, so these trucks belong on clean, dry, level floors.
Pneumatic tires look like small tractor tires and contain compressed air, usually with a tread pattern that bites into soft or uneven ground. They absorb shock well, which protects both the load and the operator on gravel, asphalt and sloping yards. Builders' suppliers, timber yards and farm-supply depots rely on them. The downside is maintenance. Pressure must be checked regularly, punctures happen, and an underinflated tire flexes at the sidewall, which reduces stability when the mast is raised.
Solid pneumatic tires, sometimes called resilient or puncture-proof tires, copy the look of an air-filled tire but are made of solid rubber or filled with a firm compound. They cannot go flat, which makes them popular in scrap yards, recycling plants, glass handling and building sites where nails and sharp offcuts are common. They ride harder than air tires and weigh more, yet they remove the downtime of punctures. Operators should still inspect them for cuts, chunking and uneven wear.
Polyurethane tires are a newer option you will meet in some warehouses, especially on pallet jacks and reach trucks. The material is lighter than rubber, wears slowly and handles heavy loads on smooth floors. Many polyurethane tires are non-marking, so they do not leave black streaks on epoxy or polished concrete. They can lose grip on wet or oily surfaces, though, and they cost more upfront. Always confirm with the supplier that the compound suits your floor and your truck's capacity.
Non-marking tires deserve a separate mention because they matter in food processing, pharmaceutical storage, clean rooms and showrooms where floor appearance is a compliance or brand concern. They are usually grey or white and use a rubber compound without the carbon black that leaves streaks. They are not a different category of tire so much as a different recipe. A cushion tire can be non-marking, and so can some solid pneumatic designs, so check the specification instead of assuming.
Every tire carries a size marking, such as 28x9-15 on a common pneumatic design. The numbers describe the tire's dimensions and the rim diameter, and they must match the truck's specification. A different size changes ground clearance, speed, braking and load stability. Never swap in a tire simply because it fits the rim. Check the data plate, the manufacturer's handbook and the supplier's advice before ordering replacements or approving any change to the tires on a truck.
The type of tire fitted also feeds into the truck's rated capacity and stability. A load chart is calculated for the truck as built, including its tire type and size. Changing from cushion to pneumatic, or fitting oversized tires, alters the centre of gravity and the track width. That is a modification, and it needs manufacturer or engineering approval before the truck returns to service. This idea sits at the heart of the attachments and modifications topics in the licence theory.
Cushion, Pneumatic and Solid Forklift Tires Compared
Cushion tires suit trucks that spend their working life indoors on smooth, sealed concrete. Typical users include distribution centres, retail back-of-house areas, factories with clean floors and cold stores. The low ride height and small turning circle let operators place pallets in tight aisles without constant repositioning. Because there is no air to leak, pressure checks are not needed, which simplifies the pre-start routine for busy teams.
Their weakness is the outdoors. A cushion-tire truck driven onto gravel, wet asphalt or a sloping dock apron loses grip quickly and transmits every bump into the mast and load. Operators should check the wear line each shift, look for chunking and flat spots, and avoid crossing debris. If your site has a short outdoor run, ask the supervisor whether the truck is approved for it first.

Pneumatic vs Cushion Forklift Tires: Which Suits Your Site?
- +Pneumatic tires absorb shock on rough, uneven ground
- +Tread pattern gives better grip on gravel, mud and wet surfaces
- +Larger diameter improves ground clearance over kerbs and drains
- +Smoother ride protects operators and fragile loads
- +Suitable for both indoor and outdoor work in many yards
- +Wide range of sizes fits many truck models and capacities
- โAir pressure needs regular checking with a proper gauge
- โPunctures can stop the truck and interrupt a shift
- โUnderinflation reduces stability when the mast is raised
- โWider footprint can limit manoeuvring in very narrow aisles
- โTire changes need a trained fitter because of stored air
- โTread may track dirt and debris onto clean indoor floors
Pros and Cons at a Glance
| Pros | Cons |
|---|---|
| Pneumatic tires absorb shock on rough, uneven ground | Air pressure needs regular checking with a proper gauge |
| Tread pattern gives better grip on gravel, mud and wet surfaces | Punctures can stop the truck and interrupt a shift |
| Larger diameter improves ground clearance over kerbs and drains | Underinflation reduces stability when the mast is raised |
| Smoother ride protects operators and fragile loads | Wider footprint can limit manoeuvring in very narrow aisles |
| Suitable for both indoor and outdoor work in many yards | Tire changes need a trained fitter because of stored air |
| Wide range of sizes fits many truck models and capacities | Tread may track dirt and debris onto clean indoor floors |
Forklift Tires Safety Checklist for Every Shift
- โPark on level ground and apply the park brake first.
- โLower the forks fully and switch the truck off.
- โWalk around every wheel in the same order each shift.
- โLook for cuts, bulges, chunking and embedded objects.
- โCompare cushion tire rubber with the moulded wear line.
- โCheck pneumatic pressure against the manufacturer's figure.
- โConfirm wheel nuts are present and look secure.
- โSweep or report debris and spills in your travel route.
- โRecord any defect on the pre-start sheet straight away.
- โTag out the truck and tell your supervisor if unsafe.
Tires are part of the stability system
A forklift's stability triangle depends on the contact points of its tires. Soft, worn or mismatched tires shift that triangle, so the truck can tip at loads and speeds that would normally be safe. Treat tire condition as a stability issue, not just a comfort or maintenance issue.
Tires wear gradually, which is exactly why operators miss the problem. Cushion tires usually show a wear line moulded into the sidewall. Once the rubber is worn down to that line, the tire has reached the end of its useful life and should be replaced, regardless of how it looks from the driver's seat. Ignoring the line means less rubber contacting the floor, longer stopping distances and a greater chance of the tire separating from its steel band.
Chunking is another common defect. Chunks of rubber break away from the tread or edge, typically from sharp debris, hard cornering or overloading. A few small nicks might be tolerable if the manufacturer's guidance permits, but large missing sections create a rough, uneven ride and can set up vibration through the mast. If you see chunking, report it and let a qualified person decide whether the truck can keep working. Do not guess about it.
Flat spots form when a truck sits for days with its weight on the same patch, or when the operator regularly locks the brakes and skids. On cushion and solid tires, flat spots cause a bumping sensation that grows worse with speed. The bumping can shift loads, strain the mast and tire the operator. Good habits help: brake smoothly, avoid wheel spin, and note in the log whenever the truck feels rough, so maintenance can inspect the tires early.
Pneumatic tires bring extra warning signs. Look for sidewall cuts, bulges, exposed cords, embedded nails or glass, damaged valves and uneven tread wear across the face of the tire. Uneven wear often points to incorrect pressure or alignment problems. A bulge means internal damage and the tire can fail without notice. Take the truck out of service immediately. Pressure should always match the manufacturer's specification, never a number guessed from experience or copied from a different truck.
Heat, chemicals and surface conditions accelerate damage. Hot concrete in a summer loading yard, oil spills in a workshop and cold-store freezing temperatures all alter rubber and polyurethane. Constant travel at high speed on short, tight routes generates heat in the tire, which weakens the bond between rubber and band. Where chemicals such as solvents or acids are present, ask the supplier whether the compound is compatible. Routine sweeping and prompt spill clean-up also protect your tires.
Worn or damaged tires directly reduce stability. A forklift is balanced like a seesaw around its front axle, and the tires form the contact patch that holds that balance. When tires are low, uneven or soft, the truck leans more in corners and under load. With a raised mast, even a small lean moves the combined centre of gravity outside the stability triangle. The outcome can be a tip-over, which is among the most serious forklift incidents.
So what should you do when you find a defect? Stop, park safely, apply the park brake, lower the forks and switch off. Tag the truck out of service according to your workplace procedure, then report it to your supervisor and record it in the pre-start sheet. Never try to continue just to finish a shift or one more pallet. A short delay is far cheaper than an injured colleague, a damaged load or a failed audit.
Removing wheels or inflating air-filled forklift tires can cause serious injury if done incorrectly, because rims are heavy and compressed air stores energy. Only a trained, authorised fitter should do this work, using the correct equipment and the manufacturer's instructions.
In Australia, forklift safety is governed by the model Work Health and Safety laws adopted in most jurisdictions, along with state-specific regulations such as those in Victoria and Western Australia. These laws require duty holders to keep plant in a safe condition, to provide information, instruction and supervision, and to consult workers. Tires are part of the plant, so a worn or mismatched tire is not a minor housekeeping issue. It is a hazard that a business must identify and control.
Operating a forklift requires a high risk work licence for the LF class, which is gained by completing the TLILIC0003 unit through a registered training organisation and being assessed as competent. The licence is issued by the relevant state or territory regulator and is valid for five years. The assessment covers pre-operational checks, safe operation, load handling and shutdown. Tires appear inside that framework because they affect everything the truck does, from braking to lifting.
Australian Standard AS 2359 covers powered industrial trucks, including their design, operation and maintenance. Manufacturers also publish handbooks that specify the tire type, size and pressure for each model. Your workplace should follow these documents, and your assessor will expect you to follow your site's procedures when you complete checks. If the handbook and workplace practice conflict, raise the matter with a supervisor rather than choosing the easier option yourself. That conversation protects you as well as the business.
Pre-start checks are the first line of defence. Most workplaces use a daily or per-shift checklist that includes tires, forks, chains, hydraulics, brakes, steering, lights, horn, seatbelt and fluid leaks. Operators are expected to complete the sheet honestly, sign it and report anything unusual. Signing a sheet without actually walking around the truck is a serious breach of trust. If an incident happens, those records will be read closely by investigators and insurers.
Tire replacement is not an operator task unless you have been trained and authorised. Removing a wheel from a forklift involves heavy components, rim hardware and, with air-filled tires, stored energy. A qualified fitter should handle the work, using the right equipment and the correct torque for the wheel nuts. After any change, a competent person should check the truck before it goes back into service and note the work in the maintenance log.
Modifications deserve special attention. Swapping tire types, fitting tire fillers or adding heavier solid tires may alter the truck's stability, speed or capacity. The same applies to attachments such as side shifters or clamps, which change the load centre and affect the data plate. Any alteration should be approved by the manufacturer or a qualified engineer, and the data plate and operator information should be updated. This is why attachments and modifications questions appear so regularly in practice tests.
Finally, licence holders should stay current. High risk work licences need renewal before they expire, and operators who return after a long break often benefit from refresher training. Tire technology, workplace rules and truck designs change over time. A habit of reading the manual, asking questions and staying alert to tire condition keeps your knowledge fresh. It also demonstrates professionalism to employers who expect their licensed operators to lead by example on site.
Start your preparation by learning the vocabulary. Terms like cushion tire, pneumatic tire, solid pneumatic, non-marking, wear line, chunking, flat spot, sidewall and data plate appear in training material and assessments. Write each term on a card with a one-line explanation and a typical workplace example. Reviewing a small deck for ten minutes a day sticks far better than a single long cramming session the night before your theory assessment.
Next, practise a physical walk-around. If you have access to a truck, or can watch an experienced operator, follow a consistent route: start at the front left tire, move around the truck clockwise, then check the forks, mast and overhead guard. Say what you see aloud. Practising out loud builds the habit of describing defects clearly, which is what an assessor wants to hear during the practical component of the licence.
Use practice questions to test understanding, not just memory. After each question, read the explanation and ask why the wrong options are wrong. For tires, you might see scenarios involving a bulge in the sidewall, a worn cushion tire or an outdoor yard with loose gravel. Choosing the correct action, usually to stop and report, becomes automatic when you have rehearsed it. Attempt the quizzes linked on this page several times, spaced over a week.
Learn to link tires to the bigger picture. Ask yourself how tire condition affects stability, braking, steering, load handling and speed. Then connect those effects to the stability triangle, load centre and capacity data plate. Assessors like candidates who can explain cause and effect rather than recite a list. For example, say that a soft pneumatic tire reduces lateral stability, which matters when the mast is raised and the load is high.
On the job, build tire awareness into your routine. Look at the floor before you drive, because debris is the main enemy of tires. Take corners slowly, avoid wheel spin and skidding, and never drive over kerbs, pallet offcuts or cables. Park on level ground with forks lowered and the brake applied, which protects tires from sitting under pressure on a bad surface. Small habits add months of life to a set of tires.
Communication matters as much as technique. If you find a tire defect, report it clearly: which truck, which wheel, what you saw and when you noticed it. Photos can help if your workplace allows them. Follow up if nobody responds, and never accept pressure to continue with a truck you believe is unsafe. A workplace that discourages reporting is a workplace you should raise with your health and safety representative.
Finish your preparation with a mixed review. Take the practice tests, check the topics you got wrong, revisit this guide and then retest. Aim to understand the reasoning behind each answer so you can handle unfamiliar wording on the day. Rest properly before your assessment, bring your identification and arrive early. With solid knowledge of forklift tires, you will walk into both the theory and practical components with the confidence of someone who truly understands the equipment.
Sample Forklift Licence Practice Questions
Try these questions from our free Forklift Licence practice tests. The correct answer and an explanation follow each question.
Under SafeWork Australia guidelines, what is the minimum requirement for a safe exclusion zone around a forklift operating area?
- A. There is no minimum โ operators use their judgement
- B. Physical barriers or clearly marked exclusion zones that separate pedestrians from forklift travel paths
- C. A verbal warning to pedestrians at the start of each shift is sufficient
- D. Yellow floor tape only, with no physical barriers needed
Answer: B. Physical barriers or clearly marked exclusion zones that separate pedestrians from forklift travel paths
SafeWork Australia's hierarchy of controls requires physical separation (barriers, bollards, exclusion zones) between pedestrian and forklift areas as the preferred control measure.
What does 'stacking height' mean in relation to forklift operations?
- A. The maximum height the forklift mast can extend
- B. The safe maximum height to which loads may be stacked in racking or freestanding
- C. The height at which the forklift's load backrest must be positioned
- D. The height restriction in the building where the forklift operates
Answer: B. The safe maximum height to which loads may be stacked in racking or freestanding
Stacking height refers to the safe maximum height to which loads may be stacked, determined by load weight, stability, racking ratings, and site-specific rules.
What penalties apply for non-compliance with WHS Legislation regulations in Australia?
- A. No penalties
- B. Significant fines (up to millions of AUD for corporations) and potential imprisonment for serious offences
- C. A verbal warning only
- D. A small administrative fee
Answer: B. Significant fines (up to millions of AUD for corporations) and potential imprisonment for serious offences
Australian WHS penalties are severe, with Category 1 offences carrying fines up to AUD 3 million and potential imprisonment.
What penalties apply for non-compliance with Load Centre Calculations regulations in Australia?
- A. No penalties
- B. Significant fines (up to millions of AUD for corporations) and potential imprisonment for serious offences
- C. A verbal warning only
- D. A small administrative fee
Answer: B. Significant fines (up to millions of AUD for corporations) and potential imprisonment for serious offences
Australian WHS penalties are severe, with Category 1 offences carrying fines up to AUD 3 million and potential imprisonment.
TLILIC0003 Questions and Answers
How this page was made: written with AI tools and published by Nathan Beja, founder of Practice Test Geeks, who is responsible for its content. Exam facts are checked against the official sources listed below. Not reviewed by a subject-matter expert. Editorial policy
Sources & references
Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy
- worksafe.nt.gov.au โ Fees, renewal ยท verified Nov 2026
- wa.gov.au โ Fees, renewal ยท verified Nov 2026
- worksafe.qld.gov.au โ Fees, renewal ยท verified Nov 2026
- worksafe.vic.gov.au โ Fees, renewal ยท verified Nov 2026
- safework.nsw.gov.au โ Fees, renewal ยท verified Nov 2026
- safeworkaustralia.gov.au โ Eligibility, registration deadline, score validity ยท verified Nov 2026




