OSHA Lock Out: A Complete Guide to Lockout/Tagout (LOTO) Rules, Steps, and Training

๐ŸŽฏ OSHA lock out explained: the 29 CFR 1910.147 standard, the 6-step LOTO procedure, training rules, and free practice questions to test your knowledge.

OSHA - Safety CertificateNov 16, 202618 min read
OSHA Lock Out: A Complete Guide to Lockout/Tagout (LOTO) Rules, Steps, and Training

An OSHA lock out procedure is the most important barrier between a worker and a machine that can start without warning. When someone clears a jam, changes a blade, or cleans a mixer, a sudden movement or energy release can cause amputations, crushing injuries, burns, or death. The rules sit in 29 CFR 1910.147, the control of hazardous energy standard. Most people call it lockout/tagout, or LOTO, and it applies across manufacturing, warehousing, food processing, and maintenance work.

The idea behind the standard is simple. Before anyone services or maintains a machine, every source of energy must be shut off, isolated, and physically prevented from coming back on. That means more than flipping a switch. Electrical power, hydraulic pressure, compressed air, steam, springs under tension, and even gravity acting on a raised load all count as hazardous energy. Each must be controlled, and each must be verified as controlled before hands go anywhere near the equipment.

OSHA estimates that proper lockout/tagout practices prevent about 120 deaths and 50,000 injuries every year among the roughly three million workers who service equipment. Despite that, the standard shows up on OSHA's list of most frequently cited violations year after year. Employers skip steps, workers use shortcuts, and procedures go stale. Understanding what the rule actually demands, and why each requirement exists, is the first step toward closing that gap on your own site.

This guide walks through the standard in plain language. You will learn who is covered, what the written energy control program must contain, how the six-step shutdown sequence works, and how locks differ from tags. We also cover group lockout, shift changes, contractor coordination, and the training categories OSHA defines. If you are studying for an osha lockout tagout (lototo) question set, this article gives you the foundation to answer scenario questions confidently.

It also helps to understand the vocabulary, because exam questions and inspectors both lean on precise terms. An authorized employee is the person who actually locks out equipment to perform service. An affected employee operates or uses the machine but does not service it. An energy-isolating device is a mechanical device, such as a circuit breaker or disconnect switch, that physically blocks the transmission of energy. A push button or selector switch does not qualify.

Another term worth learning early is the difference between lockout and tagout. A lockout device holds an energy-isolating device in the safe or off position using a key or combination lock. A tagout device is a prominent warning label that is securely fastened to the isolating device, stating that the equipment must not be operated. Locks provide physical restraint, while tags provide only a warning, which is why OSHA treats them differently throughout the standard.

Finally, remember that lockout/tagout is a program, not a single act. The standard requires written procedures, trained people, specific hardware, and annual inspections that confirm everything still works in practice. A worker who snaps a lock on a disconnect has completed one step of a much larger system. The sections below explain each part of that system, so you can recognize a compliant program, and spot a deficient one, on sight.

OSHA Lockout/Tagout by the Numbers

๐Ÿ“‹1910.147Governing Standard29 CFR, general industry
๐Ÿ‘ฅ3 millionWorkers CoveredOSHA estimate of servicing workers
๐Ÿ›ก๏ธ120Lives Saved YearlyOSHA estimate with compliance
๐Ÿ†50,000Injuries PreventedAnnual estimate
๐Ÿ”„12 monthsMaximum Inspection GapPeriodic procedure review

The Six Steps of an OSHA Lock Out Procedure

๐Ÿ“‹1. Prepare and Notify

Identify every energy source and its magnitude, then notify all affected employees that the machine will be shut down and locked out. Review the machine-specific written procedure before touching anything. Skipping this preparation is how hidden energy sources, like a secondary hydraulic line, get missed.

๐Ÿ”Œ2. Shut Down and Isolate

Stop the equipment using its normal stopping procedure, then operate the energy-isolating devices, such as disconnects, valves, or breakers, to cut each source. Isolation must be physical. Using only a stop button or a control-circuit switch does not meet the standard.

๐Ÿ”’3. Apply Lock and Tag

Each authorized employee attaches a personal lock and tag to every isolating device. The lock holds the device in the safe position, and the tag identifies who applied it and when. Only the person who applied a device should remove it, with narrow exceptions.

๐Ÿ’จ4. Release Stored Energy

Relieve, disconnect, restrain, or render safe all residual energy. Bleed pressure from hydraulic and pneumatic lines, discharge capacitors, block raised loads, and release spring tension. Stored energy can hurt workers long after the power is off, so this step is never optional.

๐Ÿ”Ž5. Verify Isolation

Before work begins, confirm the machine is truly de-energized. Try the normal start controls from a safe position, and test circuits with a meter where electrical hazards exist. Then return controls to off. Verification is the proof that the earlier steps actually worked.

The scope of 29 CFR 1910.147 is broad but not unlimited. It covers servicing and maintenance activities, including constructing, installing, setting up, adjusting, inspecting, modifying, and maintaining machines, where unexpected startup or release of energy could injure an employee. It does not generally cover construction, agriculture, or maritime work, which fall under other standards. Electrical utility work and some exposed electrical installations are handled by separate rules, so always confirm which standard applies to your industry.

Every employer with covered equipment must establish an energy control program. That program has three pillars: documented energy control procedures, employee training, and periodic inspections. The procedures must clearly state the intended use of the procedure, the specific steps for shutting down and isolating equipment, how to place and remove devices, and how to test that isolation worked. Vague or generic instructions are a common citation, because the rule expects detail for each machine type.

There is one notable exception to writing a machine-specific procedure. Employers need not document the procedure for a machine if eight conditions are all met, including that the equipment has no potential for stored or residual energy, has a single energy source that can be readily identified and isolated, and that isolation completely de-energizes it. Employers must also show that the machine is locked out during service, that a single lockout device achieves isolation, and that no hazards exist for other workers. In practice, few machines qualify.

The standard also lists situations that fall outside its scope. Work on cord-and-plug connected electrical equipment is exempt when the plug is unplugged and remains under the exclusive control of the employee doing the work. Hot tap operations on pressurized pipelines are another exception, provided continuity of service is essential and shutdown is impractical. Minor tool changes and adjustments that are routine, repetitive, and integral to production fall under the minor servicing exception, but only if alternative effective protection, such as interlocked guards, is in place.

One principle trips up many exam takers: if an energy-isolating device is capable of being locked out, the employer must use lockout unless it can prove that a tagout program provides full employee protection equal to lockout. Equipment installed or significantly modified after January 2, 1990 must be designed to accept a lockout device. Older equipment may rely on tagout only if the employer adds extra safeguards, like removing a circuit element or blocking a controlling switch.

Employers also carry duties around hardware. Lockout and tagout devices must be singularly identified, meaning used for no purpose other than controlling energy. They must be durable enough to withstand the environment, standardized by color, shape, or size, and substantial enough to prevent removal without excessive force. Tags must be legible and understandable to every worker, and must warn against hazardous conditions, such as Do Not Start or Do Not Open. Tag attachment devices need a non-reusable, self-locking design with at least a 50-pound release strength.

Documentation matters as much as hardware. Employers must keep the written procedures available and must certify periodic inspections, recording the machine inspected, the date, the employees involved, and the inspector's name. Training records must also show each employee's name and dates of training. During an OSHA inspection, a compliance officer will often start by asking for these documents and then watch a real lockout, comparing what is written against what workers actually do on the floor.

Basic OSHA Practice 1

Practice core OSHA safety questions covering hazards, worker rights, and employer responsibilities.

OSHA Lock Out Devices: Locks, Tags, and Group Lockout

A lockout device is any hardware that uses a positive means, usually a lock with a key or combination, to hold an energy-isolating device in the safe position. Typical examples include padlocks, hasps for multiple locks, valve covers, circuit breaker lockouts, and plug lockouts. Each authorized employee should use a personal lock that only they hold the key to, so that no one else can remove it by mistake.

Because locks restrain the device physically, OSHA considers them more reliable than tags. A lockout device must be strong enough to resist removal under normal conditions, so that bolt cutters or significant force would be required to defeat it. Many sites use color-coded locks by department or trade, with a name, photo, and department on a durable label, which lets anyone see immediately who is working on a machine.

Lockout vs. Tagout: Which Method Protects Workers Better?

โœ…Pros
  • +Locks physically prevent energizing, so protection does not depend on people obeying a warning
  • +Lockout is the default method OSHA expects when a device can be locked
  • +Personal locks give each worker control over their own safety
  • +Lockboxes make group lockout manageable for large maintenance crews
  • +Locks with name labels make it easy to see who is working on equipment
  • +Lockout supports a clear removal rule, because only the person who applied a lock removes it
โŒCons
  • โˆ’Lock hardware must be purchased, standardized, and stored for every authorized employee
  • โˆ’Some older equipment has no way to attach a lock, forcing the tagout route
  • โˆ’Tags alone can be ignored, removed, or misread, leaving workers exposed
  • โˆ’Tagout programs require extra safeguards to match lockout-level protection
  • โˆ’Lock removal by someone else, when the owner is absent, demands a strict documented procedure
  • โˆ’Procedures take time, which tempts workers to skip steps when production pressure runs high

OSHA Lock Out Compliance Checklist for Employers and Workers

  • โœ“Write a machine-specific energy control procedure for each piece of covered equipment.
  • โœ“Identify every energy source, including electrical, hydraulic, pneumatic, thermal, and gravitational.
  • โœ“Issue personal locks and tags that are durable, standardized, and uniquely identifiable.
  • โœ“Notify all affected employees before shutting down and locking out a machine.
  • โœ“Shut down using the normal stopping procedure before operating any isolating device.
  • โœ“Apply a lock and tag to every energy-isolating device in the safe or off position.
  • โœ“Relieve, block, or restrain all stored energy before starting any service work.
  • โœ“Verify isolation by attempting to start the machine and returning controls to off.
  • โœ“Remove locks only after the area is cleared, tools are out, and guards are replaced.
  • โœ“Inspect each procedure at least annually and keep a signed certification record.

Only the person who applied a lock removes it

The standard requires that each lockout or tagout device be removed by the employee who applied it. The only exception is when that person is unavailable and the employer follows a documented procedure, which includes confirming the worker is not on site, making a reasonable effort to contact them, and informing them before they return to work.

OSHA divides employees into three categories for training purposes, and each group needs different knowledge. Authorized employees are those who lock out or tag out machines to perform servicing or maintenance. They must understand the types of hazardous energy in the workplace, how to identify them, and the methods for isolating and controlling them. They also need to know how to apply, verify, and remove devices correctly, step by step, using the actual written procedure for each machine.

Affected employees operate or use the machine being serviced, or work in an area where servicing happens. They do not apply locks, but they must understand the purpose and use of the energy control procedure. Their most important lesson is behavioral: never attempt to start, energize, or use a machine that has been locked or tagged out. A production operator who sees a tag and restarts the line anyway can seriously injure a maintenance technician working inside.

The third group is other employees whose work operations are, or may be, in an area where energy control procedures are used. They need to recognize the procedure and understand the prohibition against restarting or reenergizing equipment that is locked or tagged out. Think of forklift drivers, janitors, and visiting contractors. They are not trained to perform lockout, but they must know what a lock and tag mean and why they must never be disturbed.

Employers must provide training before an employee first performs or is affected by the procedures, and they must retrain whenever circumstances change. Retraining is required when an employee is reassigned to a new job that changes their duties, when there is a change in machines, equipment, or processes that creates a new hazard, or when the energy control procedure itself changes. It is also required if an inspection reveals deficiencies or the employer has reason to believe knowledge is lacking.

Good training goes beyond slides and quizzes. The strongest programs include hands-on practice at the real machine, where employees walk through each step and find the actual isolation points. For example, a packaging line might have a main electrical disconnect, a compressed-air supply valve, and a spring-loaded cutting head. Trainees learn that locking only the disconnect would leave two energy sources active, and that verification, not assumption, proves the machine is safe.

Employers must also certify that training has been completed and kept up to date. The certification should show each employee's name and the training dates, and records must be kept available for review. Many companies pair this with short refreshers during safety meetings. Toolbox talks work well for this, because a ten-minute discussion of a near miss or a recent procedure change keeps lockout practices current without taking crews away from their jobs for long.

Authorized employees also learn the limits of their authority. They must never remove another person's lock, never bypass an interlock to speed up a job, and never assume that a machine is safe because it looks stopped. A flywheel can keep turning, a hydraulic accumulator can hold pressure for hours, and a capacitor can retain a lethal charge. Training should repeat these examples until they become reflexes that workers apply automatically.

Lockout/tagout violations are among the most frequently cited by federal OSHA, ranking in the top ten general industry citations in recent years, with thousands of citations annually. Inspectors commonly find missing or inadequate written procedures, workers who were never trained, no periodic inspections, and devices that were not applied to every energy source. Because these failures are easy to spot during a walkaround, they often become entry points to broader inspections of a facility's overall safety management.

Penalties can be steep. As of recent adjustments, a serious violation can carry a fine of more than $16,000 per violation, while willful or repeated violations can exceed $165,000 each. Figures adjust annually for inflation, so check the current schedule on OSHA's website. A fatality investigation involving a machine startup can also trigger a willful classification, referrals for criminal prosecution in extreme cases, and costly civil lawsuits that dwarf the original fine amount.

Real incidents show how quickly things go wrong. A worker clearing a jam in a conveyor, believing the machine was stopped, loses an arm when a coworker presses the start button from a control panel. A technician entering a mixer to clean it is trapped when someone restores power. In both situations, a lock on the disconnect and a clear tag would have prevented the injury. These tragedies share a root cause: a procedure existed but was not followed.

The most common shortcut is relying on the stop button or a control circuit switch instead of the isolating device. Control circuits can fail, and a stuck relay or a software command can restart a machine. Another frequent error is failing to verify isolation. Workers lock the disconnect and start working without testing, only to discover that a second energy source, like a pneumatic line, was still live. Verification takes seconds and prevents the worst outcomes.

Another repeating problem is incomplete handling of contractors and temporary workers. A company may train its own staff well, then bring in an outside crew who never see the energy control procedure. OSHA expects the host employer and the contractor to inform each other of their lockout rules and make sure their employees understand them. Documenting that exchange, even with a one-page sign-off, protects both parties and gives an inspector evidence that coordination actually occurred.

Periodic inspections are the safety net that catches drift. At least annually, an authorized employee other than the ones using the procedure must review each procedure, observing a real lockout or discussing steps with the employees. For tagout procedures, the review must include a discussion of the limitations of tags. The inspector certifies the date, machine, employees, and their own name. Skipping this review is a cited violation by itself, even if no one has been hurt.

Companies that rarely face lockout citations tend to share habits: they audit procedures when equipment is modified, they encourage workers to stop a job when something looks wrong, and managers refuse to push for speed over safety. They also treat near misses as lessons. If a worker finds a machine with an unexpected energy source, that finding updates the procedure, retrains the crew, and prevents a repeat. Compliance becomes a living process rather than a binder on a shelf.

If you are preparing for an OSHA 10 or OSHA 30 exam, or a workplace safety assessment, start by memorizing the six steps in order: prepare, shut down, isolate, apply devices, release stored energy, and verify. Exam writers love to scramble the order or hide a step inside a scenario. If a question describes a worker who applies a lock and begins work without checking for residual energy, you should immediately spot the missing step.

Next, learn the definitions cold. Know the difference between authorized, affected, and other employees, since training questions hinge on it. Know what qualifies as an energy-isolating device and what does not. A circuit breaker, disconnect switch, and manually operated valve qualify. A push button, selector switch, and other control circuit devices do not. Many wrong answers on practice tests rely on this exact distinction, so build flashcards around it.

Use scenario thinking. When you read a question, picture the machine and list its energy sources before reading the answer choices. A hydraulic press has electrical power, hydraulic pressure, and gravity acting on the ram. A conveyor has electrical power and possibly tension in belts or springs. This habit trains you to notice what a given answer ignores. It also mirrors how real safety professionals evaluate machines before writing a procedure for them.

Pay attention to numbers and timing. Periodic inspections occur at least annually. Tag attachment devices need a minimum 50-pound release strength. Retraining follows changes in job duties, equipment, processes, or procedures. Equipment installed after January 2, 1990 must accept a lockout device. These specific facts make easy points on a test, and they also matter in real audits, where inspectors check dates, records, and equipment details against the written program.

Take timed practice tests regularly, and review every missed question rather than only checking your score. When you miss one, write a one-line rule that explains the correct answer, then revisit it two days later. Mixing lockout questions with hazard communication, electrical safety, and confined space topics also helps, because real exams jump between subjects, and your recall needs to handle that switching without losing accuracy or confidence.

On the job, build habits that outlast any exam. Carry your own lock and tag, read the machine-specific procedure every time rather than trusting memory, and test the start controls even when you are rushed. Speak up when you see a missing lock or an unmarked energy source. A short pause to confirm isolation costs seconds, while an injury can end a career, so make verification a personal rule that never changes.

Finally, pair formal study with workplace learning. Ask your safety coordinator to show you the energy control procedures for your area, and walk through them at the machines. Attend safety meetings where lockout is discussed, and volunteer to help with the annual procedure review. Experience at the actual equipment makes the written rules concrete, and it turns textbook knowledge into reliable judgment that serves you on both the exam and the floor.

OSHA Basic OSHA Practice 3

Challenge yourself with another full-length OSHA practice test on workplace safety essentials.

OSHA Confined Space Entry 1

Learn permit-required confined space rules, atmospheric testing, and energy isolation before entry.

OSHA Questions and Answers

How this page was made: written with AI tools and published by Nathan Beja, founder of Practice Test Geeks, who is responsible for its content. Exam facts are checked against the official sources listed below. Not reviewed by a subject-matter expert. Editorial policy

Sources & references

Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy

  1. osha.gov โ€” Score validity, test delivery, eligibility, passing score, renewal, retake policy, score release ยท verified Nov 2026