
456A Practice Test
Updated November 2026Facts verified Oct 21, 2026 against Skilled Trades Ontario (STO), which runs the Interprovincial Red Seal exam for Welder 456A in Ontario
The 456A has 125 questions, takes about 4 hours and costs 150 CAD[1][2][3] (Skilled Trades Ontario (STO), which runs the Interprovincial Red Seal exam for Welder 456A in Ontario, verified Oct 21, 2026).
- The Red Seal Welder exam has 125 multiple-choice questions based on the Red Seal Occupational Standard.[1]
- Candidates get up to four hours to write the Red Seal Welder 456A certifying exam in Ontario.[2]
- The pass mark for the Red Seal Welder 456A certifying exam in Ontario is 70%.[2]
- The Red Seal Welder 456A certifying exam costs $150 plus HST, paid through the Skilled Trades Ontario Portal.[3]
- Completed Ontario apprentices write the Welder 456A exam free the first time, and each retake costs $150 plus HST.[4]
- Candidates who fail the Red Seal Welder 456A exam in Ontario must wait 30 days and pay the exam fee again before they rebook.[3]
- Welder 456A is a non-compulsory trade in Ontario, so the Certificate of Qualification earned by passing the exam does not need to be renewed.[5]
- Ontario does not require Welder 456A Certificate of Qualification holders to renew, because welding is a non-compulsory trade.[5]
- The Red Seal Welder 456A exam is taken on the rsexam.ca online system at Skilled Trades Ontario exam sites, including STO headquarters and Ontario college campuses.[3]
Numbers in brackets link to the official sources listed under Sources & last verified. Dates that have passed are removed automatically.
456A Exam at a Glance
What are the key eligibility requirements for the 456A?
Candidates must meet the educational and professional requirements set by the Canadian certification body. Check official prerequisites before applying.
Start FREE TestWhat is the best strategy for 456A exam preparation?
Combine official study materials with practice tests, focus on weak areas, and create a structured revision timetable leading up to exam day.
Start FREE TestHow is the 456A exam scored?
The 456A uses a standardised scoring system. Results are typically provided as pass/fail, with detailed score reports available for each domain area.
Start FREE TestWhat should I bring on 456A exam day?
Bring valid photo identification, your exam confirmation, and any approved materials. Arrive early and review the testing centre rules beforehand.
Start FREE TestWhat the 456A is and how it works
According to Skilled Trades Ontario (STO), which runs the Interprovincial Red Seal exam for Welder 456A in Ontario, “This trade's Red Seal exam has 125 questions”[1]
The 456A exam is the Interprovincial Red Seal exam for the Welder trade. In Ontario, Skilled Trades Ontario (STO) runs it. If you pass, STO issues a Certificate of Qualification. Welder is a non-compulsory trade, so the certificate does not have to be renewed and does not expire.
Delivery and format. You write the exam online through the rsexam.ca system at an STO or college exam site in Ontario. It has 125 multiple-choice questions, and you have up to 4 hours to finish.
Scoring and results. The pass score is 70%. When your exam has been marked, STO emails you if it has your email address, and you can see your results on the STO Portal.
Eligibility. When you complete an Ontario apprenticeship, you receive a 1-year Provisional C of Q and an Authorization to Test Letter. You need that letter to book the exam. Other routes into the exam have their own rules, so check with STO if you did not finish an Ontario apprenticeship.
Fees and retakes. The exam fee is $150 + HST, paid through your STO Portal account. For completed Ontario apprentices, the first attempt is free. If you do not pass, you must wait 30 days before you retake the exam, and you pay $150 + HST for each retake. Fees and procedures can change, and other provinces run the exam their own way, so confirm the details on the Skilled Trades Ontario website before you book.
456A content outline and where to practise each area
The content areas below are copied from the official 456A content outline published by Skilled Trades Ontario (STO), which runs the Interprovincial Red Seal exam for Welder 456A in Ontario, with the share of the exam each area carries. The right-hand column shows which of our practice sets covers it.
| Official content area | Weight | Practice on this site |
|---|---|---|
| Performs common occupational skills[6] | 16% | Mixed practice tests above Practise shop safety, PPE, hazard control, codes and standards, and the inspection and testing methods used to judge weld quality. |
| Performs cutting and gouging[6] | 18% | 456A Oxyfuel Welding & Cutting Practise oxyfuel equipment setup, flame types, cylinder and hose safety, and how cutting and gouging methods suit different metals and thicknesses. |
| Performs layout and fabrication of components for welding[6] | 22% | 456A Blueprint Reading, Weld Symbols & Joi... Practise reading drawings and weld symbols, choosing joint designs and edge preparation, and controlling fit-up and distortion. |
| Performs welding processes[6] | 44% | 456A SMAW (Shielded Metal Arc Welding) Practise settings, consumables, shielding, positions and defect causes for SMAW, GMAW, FCAW and GTAW, using the separate process sets as well. |
456A Practice Test Questions
Worked examples: how to reason through 456A questions
These are practice questions written for this site, not questions from the real exam. Each explanation shows why the right answer is right and why the others are wrong.
Example 1
Question: What is the purpose of a bend test in weld qualification?
- To test if the weld can be straightened
- To evaluate weld ductility, fusion, and soundness by bending a specimen to a specified radius and examining the outer surface for cracks or discontinuities exceeding the acceptance criteria
- To test the hardness of the weld
- To determine the weld's tensile strength
Answer: B. To evaluate weld ductility, fusion, and soundness by bending a specimen to a specified radius and examining the outer surface for cracks or discontinuities exceeding the acceptance criteria
Explanation:
B is correct. In a guided bend test, a specimen cut from a test weld is bent to a set radius. The outer surface is stretched the most, so cracks, lack of fusion and other discontinuities open up and show. Each one is compared with the acceptance criteria. This checks ductility, fusion and soundness together.
- A is wrong because the test bends the specimen on purpose. Its aim is not to straighten anything.
- C is wrong because hardness is measured with a separate hardness test.
- D is wrong because tensile strength comes from a tensile test, where the specimen is pulled until it breaks.
Rule to remember: bend tests show soundness and ductility, tensile tests measure strength and hardness tests measure hardness. Face, root and side bends each examine a different surface of the weld.
Example 2
Question: What does 'wire stick-out' (contact tip-to-work distance) affect in GMAW?
- Current draw and deposition rate — longer stick-out reduces current and deposition rate
- Shielding gas coverage and arc voltage only
- Wire feed speed setting at the machine
- Contact tip wear rate only
Answer: A. Current draw and deposition rate — longer stick-out reduces current and deposition rate
Explanation:
A is correct. Stick-out is the length of wire between the contact tip and the work. Welding current flows through this length, and it heats up from electrical resistance. With a longer stick-out, resistance goes up and the wire is preheated. At the same wire feed speed the machine draws less current, so penetration drops. Deposition changes too.
- B is wrong because stick-out can affect gas coverage, but its main effect is on current, so "only" makes this option false.
- C is wrong because wire feed speed is set at the machine. Stick-out does not change that setting.
- D is wrong because tip wear is a minor side effect, not the main one.
Rule to remember: in GMAW, longer stick-out means lower current and shallower penetration. Shorter stick-out means higher current and deeper penetration. Keep stick-out steady to get consistent welds.
Example 3
Question: On a drawing, a fillet weld symbol has a '(E)' notation. What does this indicate?
- The effective throat dimension is specified (rather than the leg size)
- The weld is to be made by an experienced welder only
- The electrode type is specified separately in the welding schedule
- Equal-leg fillet weld with both legs equal to the specified dimension
Answer: A. The effective throat dimension is specified (rather than the leg size)
Explanation:
A is correct. When the letter E appears with a fillet weld size, the dimension is the effective throat, not the leg length. Engineers do this when their stress calculations need a specific throat. The fabricator then works out the leg size needed to reach that throat.
- B is wrong because weld symbols describe the weld itself. Welder qualification is handled through procedures and testing.
- C is wrong because the electrode is named in the welding procedure or in the tail of the symbol. A letter next to the size does not do this.
- D is wrong because a single size on a fillet symbol already means equal legs. No E is needed for that.
Rule to remember: a plain fillet size is the leg length, and a size marked with E is the effective throat. Always check which one the drawing gives before you set your leg size.
How to use these practice tests
Start with the official outline. Download the STO Exam Preparation Guide and the Red Seal exam information for Welder. Compare the weightings: welding processes is the largest area at 44%, then layout and fabrication at 22%, cutting and gouging at 18% and common occupational skills at 16%. Plan your study time to match those weightings.
Take a baseline test. Do the free 456A practice test without notes, and list the topics where you lost marks.
Work by topic. Spend most of your time on the process sets: SMAW Stick, GMAW MIG, FCAW and GTAW TIG. Then cover welding symbols, metallurgy and weld quality control. For every wrong answer, read the explanation and write down the rule in your own words.
Link it to the shop. When a question covers a setting or a defect, think about where you have seen it on the job. Ask a journeyperson about anything that is unclear.
Rehearse the real exam. Before test day, do a timed mixed session. Practise pacing yourself so you can review flagged questions before the 4 hours run out. Then go back over your weak topics once more.
456A FAQ
Sources & last verified
- red-seal.ca — number of questions (official source). “This trade's Red Seal exam has 125 questions” Verified Oct 21, 2026.
- Skilled Trades Ontario (STO), which runs the Interprovincial Red Seal exam for Welder 456A in Ontario — time limit, passing score, score release (official source). “You will have up to four hours to write your examination.” Verified Oct 21, 2026.
- Skilled Trades Ontario (STO), which runs the Interprovincial Red Seal exam for Welder 456A in Ontario — exam fee, retake policy, delivery (official source). “Pay your exam fee of $150 + HST on the Skilled Trades Ontario Portal account and sign into your account to complete payment.” Verified Oct 21, 2026 · source checked Oct 20, 2026.
- Skilled Trades Ontario (STO), which runs the Interprovincial Red Seal exam for Welder 456A in Ontario — retake fee, eligibility (official source). “If you don’t pass on the first attempt, you will need to pay the standard fee of $150 + HST for each additional try.” Verified Oct 21, 2026.
- Skilled Trades Ontario (STO), which runs the Interprovincial Red Seal exam for Welder 456A in Ontario — validity, renewal (official source). “Because this trade is non-compulsory, this certificate does not have to be renewed” Verified Oct 21, 2026.
- red-seal.ca — other (official source). “performs common occupational skills 16%” Verified Oct 21, 2026.
How we verify: editorial & fact-checking policy. Report an error: contact us.
How this page was made: written with AI tools and published by Nathan Beja, founder of Practice Test Geeks, who is responsible for its content. Exam facts are checked against the official sources listed below. Not reviewed by a subject-matter expert. Editorial policy
Sources & references
Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy
- red-seal.ca — Exam format, exam information · verified Nov 2026
- skilledtradesontario.ca — Passing score, score release, time limit, renewal, score validity, eligibility, retake fee, test delivery, fees, retake policy · verified Nov 2026