The Red Seal Welder 456A exam is written by welders in Ontario who want a Certificate of Qualification from Skilled Trades Ontario (STO). Many are completed apprentices who hold a 1-year Provisional C of Q. This page gives you free practice sets for each part of the exam outline, worked answers to sample questions, the official exam facts and a study plan you can follow.
The 456A has 125 questions, takes about 4 hours and costs 150 CAD[1][2][3] (Skilled Trades Ontario (STO), which runs the Interprovincial Red Seal exam for Welder 456A in Ontario, verified Oct 21, 2026).
Numbers in brackets link to the official sources listed under Sources & last verified. Dates that have passed are removed automatically.
According to Skilled Trades Ontario (STO), which runs the Interprovincial Red Seal exam for Welder 456A in Ontario, “This trade's Red Seal exam has 125 questions”[1]
The 456A exam is the Interprovincial Red Seal exam for the Welder trade. In Ontario, Skilled Trades Ontario (STO) runs it. If you pass, STO issues a Certificate of Qualification. Welder is a non-compulsory trade, so the certificate does not have to be renewed and does not expire.
Delivery and format. You write the exam online through the rsexam.ca system at an STO or college exam site in Ontario. It has 125 multiple-choice questions, and you have up to 4 hours to finish.
Scoring and results. The pass score is 70%. When your exam has been marked, STO emails you if it has your email address, and you can see your results on the STO Portal.
Eligibility. When you complete an Ontario apprenticeship, you receive a 1-year Provisional C of Q and an Authorization to Test Letter. You need that letter to book the exam. Other routes into the exam have their own rules, so check with STO if you did not finish an Ontario apprenticeship.
Fees and retakes. The exam fee is $150 + HST, paid through your STO Portal account. For completed Ontario apprentices, the first attempt is free. If you do not pass, you must wait 30 days before you retake the exam, and you pay $150 + HST for each retake. Fees and procedures can change, and other provinces run the exam their own way, so confirm the details on the Skilled Trades Ontario website before you book.
The content areas below are copied from the official 456A content outline published by Skilled Trades Ontario (STO), which runs the Interprovincial Red Seal exam for Welder 456A in Ontario, with the share of the exam each area carries. The right-hand column shows which of our practice sets covers it.
| Official content area | Weight | Practice on this site |
|---|---|---|
| Performs common occupational skills[6] | 16% | Mixed practice tests above Practise shop safety, PPE, hazard control, codes and standards, and the inspection and testing methods used to judge weld quality. |
| Performs cutting and gouging[6] | 18% | 456A Oxyfuel Welding & Cutting Practise oxyfuel equipment setup, flame types, cylinder and hose safety, and how cutting and gouging methods suit different metals and thicknesses. |
| Performs layout and fabrication of components for welding[6] | 22% | 456A Blueprint Reading, Weld Symbols & Joi... Practise reading drawings and weld symbols, choosing joint designs and edge preparation, and controlling fit-up and distortion. |
| Performs welding processes[6] | 44% | 456A SMAW (Shielded Metal Arc Welding) Practise settings, consumables, shielding, positions and defect causes for SMAW, GMAW, FCAW and GTAW, using the separate process sets as well. |
These are practice questions written for this site, not questions from the real exam. Each explanation shows why the right answer is right and why the others are wrong.
Question: What is the purpose of a bend test in weld qualification?
Answer: B. To evaluate weld ductility, fusion, and soundness by bending a specimen to a specified radius and examining the outer surface for cracks or discontinuities exceeding the acceptance criteria
Explanation:
B is correct. In a guided bend test, a specimen cut from a test weld is bent to a set radius. The outer surface is stretched the most, so cracks, lack of fusion and other discontinuities open up and show. Each one is compared with the acceptance criteria. This checks ductility, fusion and soundness together.
Rule to remember: bend tests show soundness and ductility, tensile tests measure strength and hardness tests measure hardness. Face, root and side bends each examine a different surface of the weld.
Question: What does 'wire stick-out' (contact tip-to-work distance) affect in GMAW?
Answer: A. Current draw and deposition rate — longer stick-out reduces current and deposition rate
Explanation:
A is correct. Stick-out is the length of wire between the contact tip and the work. Welding current flows through this length, and it heats up from electrical resistance. With a longer stick-out, resistance goes up and the wire is preheated. At the same wire feed speed the machine draws less current, so penetration drops. Deposition changes too.
Rule to remember: in GMAW, longer stick-out means lower current and shallower penetration. Shorter stick-out means higher current and deeper penetration. Keep stick-out steady to get consistent welds.
Question: On a drawing, a fillet weld symbol has a '(E)' notation. What does this indicate?
Answer: A. The effective throat dimension is specified (rather than the leg size)
Explanation:
A is correct. When the letter E appears with a fillet weld size, the dimension is the effective throat, not the leg length. Engineers do this when their stress calculations need a specific throat. The fabricator then works out the leg size needed to reach that throat.
Rule to remember: a plain fillet size is the leg length, and a size marked with E is the effective throat. Always check which one the drawing gives before you set your leg size.
Start with the official outline. Download the STO Exam Preparation Guide and the Red Seal exam information for Welder. Compare the weightings: welding processes is the largest area at 44%, then layout and fabrication at 22%, cutting and gouging at 18% and common occupational skills at 16%. Plan your study time to match those weightings.
Take a baseline test. Do the free 456A practice test without notes, and list the topics where you lost marks.
Work by topic. Spend most of your time on the process sets: SMAW Stick, GMAW MIG, FCAW and GTAW TIG. Then cover welding symbols, metallurgy and weld quality control. For every wrong answer, read the explanation and write down the rule in your own words.
Link it to the shop. When a question covers a setting or a defect, think about where you have seen it on the job. Ask a journeyperson about anything that is unclear.
Rehearse the real exam. Before test day, do a timed mixed session. Practise pacing yourself so you can review flagged questions before the 4 hours run out. Then go back over your weak topics once more.
The Red Seal Welder exam has 125 multiple-choice questions, and you have up to 4 hours to finish. In Ontario, you write it online through the rsexam.ca system at a Skilled Trades Ontario or college exam site. The questions follow the official outline, and welding processes carry the most weight at 44%.
You need 70% to pass. Skilled Trades Ontario uses this pass score for both provincial and Interprovincial certifying exams. Once your exam is marked, STO emails you if it has your email address on file, and your results appear on your Skilled Trades Ontario Portal account.
The exam fee is $150 + HST, paid through your Skilled Trades Ontario Portal account. If you completed an Ontario apprenticeship, your first attempt is free. If you do not pass, each extra attempt costs $150 + HST. Check the STO website for current fees before you book.
You must wait 30 days before you can retake the exam, and you pay the $150 + HST fee again before you reschedule. Use the waiting period to work on the content areas where you scored lowest, using the topic practice sets and the official exam preparation material.
When you complete an Ontario apprenticeship, Skilled Trades Ontario issues a 1-year Provisional Certificate of Qualification and emails you an Authorization to Test Letter. If STO has no email address for you, the letter comes by mail. You need this letter to schedule your exam through the STO Portal.
No. Welder is a non-compulsory trade in Ontario, so the Certificate of Qualification that Skilled Trades Ontario issues after you pass does not have to be renewed and does not expire. Employers or particular jobs may still ask for separate welding qualification tests.
How we verify: editorial & fact-checking policy. Report an error: contact us.