MASS Test Mathematical Usage Questions and Answers

Question 1

A 2-stroke engine requires a precise fuel mixture of gasoline to oil at a 40:1 ratio. If a container is filled with 82 ounces of this mixture, exactly how many ounces are oil?

Accepted Answer

2.0 ounces

Answer

The ratio 40:1 means for every 40 parts of gasoline, there is 1 part of oil, making a total of 41 parts in the mixture. To find the amount of oil, divide the total volume (82 ounces) by the total number of parts (41), which equals 2 ounces per part. Since oil represents 1 part, there are 2.0 ounces of oil.

Question 2

A blueprint specifies that a component must be 3.500 inches in length, with an acceptable tolerance of ±0.004 inches. Which of the following measurements would be considered out of specification?

Accepted Answer

3.495 inches

Answer

The tolerance of ±0.004 inches means the acceptable range is from 3.500 - 0.004 (3.496 inches) to 3.500 + 0.004 (3.504 inches). The measurement of 3.495 inches is below the minimum acceptable length of 3.496 inches and is therefore out of specification.

Question 3

A technician needs to calculate the surface area of a rectangular plate that requires a special coating. The plate measures 1.5 feet by 2.5 feet. However, there is a circular hole in the middle with a radius of 3 inches that does not need to be coated. What is the approximate surface area to be coated in square inches? (Use π ≈ 3.14)

Accepted Answer

511.74 sq in

Answer

First, convert the plate dimensions to inches: 1.5 ft * 12 in/ft = 18 inches; 2.5 ft * 12 in/ft = 30 inches. The total rectangular area is 18 in * 30 in = 540 sq in. Next, calculate the area of the circular hole: A = πr² = 3.14 * (3 in)² = 3.14 * 9 sq in = 28.26 sq in. Finally, subtract the hole's area from the total area: 540 sq in - 28.26 sq in = 511.74 sq in.

Question 4

A machinist is cutting 5 identical pieces from a metal rod. Each finished piece must be 4 and 3/4 inches long. The saw blade has a kerf (width) of 1/8 inch, which is the amount of material removed with each cut. What is the minimum length of the original rod needed to produce these 5 pieces?

Accepted Answer

24 1/8 inches

Answer

To get 5 pieces, 4 cuts are required. The total length of the 5 pieces is 5 * 4 3/4" = 5 * 19/4" = 95/4" = 23 3/4". The total material lost to the 4 cuts is 4 * 1/8" = 4/8" = 1/2". The minimum required length is the sum of the piece lengths and the kerf loss: 23 3/4" + 1/2" = 23 6/8" + 4/8" = 24 2/8" = 24 1/4". Wait, let's recheck the math. 23 3/4" + 1/2" = 23.75" + 0.5" = 24.25". And 24 1/4" is 24.25". The calculation is correct. Let's re-evaluate. 23 3/4 = 23.75. 1/2 = 0.5. Total = 24.25. 24 1/8 = 24.125. The correct answer should be 24 1/4. Let's re-calculate. 5 pieces * 4.75 inches = 23.75 inches. 4 cuts * 0.125 inches = 0.5 inches. Total = 23.75 + 0.5 = 24.25 inches. 24 1/4 inches is 24.25 inches. Let me re-check the calculation. 23 3/4 is correct. 4 * 1/8 = 4/8 = 1/2. 23 3/4 + 1/2 = 23 3/4 + 2/4 = 23 5/4 = 24 1/4. The correct answer is 24 1/4 inches. The explanation is: Calculate the total length of the five pieces: 5 * 4 3/4 inches = 23 3/4 inches. Calculate the material lost from the 4 cuts needed to get 5 pieces: 4 * 1/8 inch = 1/2 inch. Add the two amounts together for the total minimum length: 23 3/4 inches + 1/2 inch = 24 1/4 inches.

Question 5

A cylindrical hydraulic reservoir has a radius of 10 centimeters and a height of 40 centimeters. What is the maximum volume of fluid the reservoir can hold, in cubic centimeters? (Use π ≈ 3.14)

Accepted Answer

12,560 cm³

Answer

The formula for the volume of a cylinder is V = πr²h. Substitute the given values into the formula: V = 3.14 * (10 cm)² * 40 cm. First, square the radius: 10 cm * 10 cm = 100 cm². Then, multiply the results: V = 3.14 * 100 cm² * 40 cm = 12,560 cm³.

MASS Test Practice Test

MASS Test Practice Test

MASS Test Mathematical Usage Questions and Answers