ASE L3 Supporting Systems — Questions and Answers
Question 1: A technician is replacing the HV electric A/C compressor on a hybrid vehicle. Which refrigerant oil must be used when servicing the system?
- Standard PAG oil used on belt-driven compressors
- The POE (polyol ester) oil specified by the manufacturer (Correct answer)
- Mineral oil, to prevent seal swelling
- Any universal oil, provided the viscosity matches
Correct answer: The POE (polyol ester) oil specified by the manufacturer
Electric compressors have the HV motor windings exposed to the refrigerant and oil, so they require the manufacturer-specified electrically insulating oil, typically POE. Using the wrong oil can degrade insulation and set an isolation fault.
In a hybrid or EV with a sealed electric compressor, the refrigerant and oil circulate around the HV motor. The oil therefore has to be a good electrical insulator, which is why manufacturers specify POE oil. Conventional PAG oil can absorb moisture and conduct enough to lower insulation resistance. Contamination or the wrong oil can cause HV isolation faults and compressor failure. Always use the specified oil type and quantity, and dedicated recovery equipment to avoid cross-contamination.
Question 2: A hybrid uses a brake-by-wire system with a stroke simulator. During a normal brake application, what is the stroke simulator's function?
- It multiplies pedal force to boost the master cylinder output
- It stores brake fluid under pressure for ABS operation
- It applies the parking brake when the vehicle stops
- It provides pedal feel while the driver's master cylinder pressure is isolated from the wheel circuits (Correct answer)
Correct answer: It provides pedal feel while the driver's master cylinder pressure is isolated from the wheel circuits
In brake-by-wire systems the pedal's master cylinder is isolated and feeds the simulator, giving normal pedal feel. The brake ECU separately controls wheel brake pressure to blend regenerative and hydraulic braking.
With brake blending, the ECU decides how much braking comes from the motor-generator and how much from friction brakes. To do that, the driver's master cylinder is isolated from the wheel circuits during normal operation. A stroke simulator absorbs the displaced fluid and provides a natural pedal feel and travel. The pedal stroke sensors tell the ECU the driver's demand, and the actuator generates wheel pressure. If the system fails, a fail-safe mode reconnects the master cylinder to the wheel brakes.
Question 3: After refilling the power electronics (inverter) coolant loop on a hybrid, what is the correct way to purge trapped air?
- Run the electric coolant pump using a scan tool active test and top off as air is released (Correct answer)
- Idle the engine with the cap off until the upper hose is hot
- Open the HV battery coolant fitting until fluid appears
- Drive the vehicle at highway speed to purge air naturally
Correct answer: Run the electric coolant pump using a scan tool active test and top off as air is released
The inverter loop uses a separate electric pump, so the pump is run via the scan tool's active test to circulate coolant and bleed air. Level is then rechecked and topped off.
Hybrid power electronics usually have a dedicated low-temperature coolant loop with an electric water pump and reservoir, separate from the engine cooling circuit. Air trapped in this loop can cause overheating of the inverter or converter and trigger a warning. Manufacturers specify filling to the proper level and activating the pump with a scan tool or a defined power-mode procedure. Recheck the reservoir level after purging, and use only the specified coolant type.
Question 4: On a SAE J1772 charging connection, what information does the duty cycle of the control pilot signal communicate to the vehicle?
- The state of charge of the HV battery
- The grid frequency at the supply outlet
- The maximum current the EVSE can supply (Correct answer)
- The AC voltage present at the connector
Correct answer: The maximum current the EVSE can supply
The EVSE sends a 1 kHz PWM pilot signal whose duty cycle tells the vehicle the maximum available charging current. The vehicle then limits its draw to that value.
The control pilot circuit lets the EVSE and vehicle communicate. The EVSE generates a 1 kHz signal, and its duty cycle encodes the maximum continuous current available. The vehicle also changes the pilot voltage level via a resistor to indicate states such as connected or ready to charge. The proximity pin tells the vehicle the connector is latched and sets cable current rating. Together they ensure power is only energized when the connection is safe.
Question 5: A Level 2 EVSE is hardwired to a dedicated 240 V, 40 A branch circuit. Based on the continuous-load rule, what is the maximum continuous charging current the EVSE should be set to deliver?
- 40 A
- 32 A (Correct answer)
- 24 A
- 16 A
Correct answer: 32 A
Continuous loads are limited to 80% of the breaker rating, and 80% of 40 A is 32 A.
EV charging is treated as a continuous load because it can run for three hours or more. Electrical code therefore requires the circuit to be rated at 125% of the load, which is the same as limiting the load to 80% of the circuit rating. A 40 A breaker supports 32 A continuous, which at 240 V is about 7.7 kW. Likewise, a 20 A, 120 V circuit supports 16 A, and a 15 A circuit supports 12 A. Installation must also use properly rated conductors and a dedicated circuit.
Question 6: A customer uses a Level 1 cord set with a 120 VAC household outlet. Which statement describes this charging method?
- It delivers about the same power as a Level 2 EVSE
- It requires a DC fast-charge connector
- It has the slowest charging rate and is limited by the outlet circuit's capacity (Correct answer)
- It bypasses the vehicle's onboard charger
Correct answer: It has the slowest charging rate and is limited by the outlet circuit's capacity
Level 1 charging uses a 120 VAC outlet and is the slowest, typically about 1.4 kW at 12 A. It still goes through the onboard charger and is limited by the circuit.
Level 1 charging uses a standard 120 VAC outlet, usually on a 15 A or 20 A circuit, and the cord set contains the EVSE control electronics. At the 12 A continuous limit of a 15 A circuit, power is only about 1.4 kW, so adding range takes many hours. The AC power is converted to DC by the vehicle's onboard charger. Level 2 uses 208 to 240 VAC and offers several times more power. DC fast charging bypasses the onboard charger and feeds DC directly to the battery.
Question 7: What is required for a vehicle to perform true vehicle-to-grid (V2G) power export?
- A larger 12 V auxiliary battery
- A Level 1 cord set with a ground-fault interrupter
- A conventional unidirectional onboard charger
- A bidirectional power path and a grid-compliant EVSE that can communicate with the vehicle and utility (Correct answer)
Correct answer: A bidirectional power path and a grid-compliant EVSE that can communicate with the vehicle and utility
V2G needs hardware capable of reversing power flow plus a grid-interconnection-compliant EVSE or inverter with communication. A one-way charger cannot export energy.
A standard onboard charger only converts AC to DC for charging. V2G requires bidirectional capability, either with an onboard bidirectional charger/inverter or with a DC-side bidirectional EVSE. The equipment must meet utility interconnection requirements, including anti-islanding protection and communication. This also lets the system limit discharge to protect battery state of charge and the owner's driving needs. Simple vehicle-to-load outlets are different because they power local devices without exporting to the grid.
Question 8: In an electric power steering (EPS) system, which inputs does the control module primarily use to calculate the amount of motor assist?
- Steering column torque sensor signal and vehicle speed (Correct answer)
- HV battery voltage and cabin temperature
- Brake pedal position and ambient light
- A/C compressor speed and coolant temperature
Correct answer: Steering column torque sensor signal and vehicle speed
The EPS ECU uses the torque sensor to measure driver effort and vehicle speed to scale the assist, giving more help at low speed. It then commands the assist motor accordingly.
Electric power steering replaces the hydraulic pump with an electric motor on the column or rack. A torque sensor in the steering shaft measures the twisting force applied by the driver. The ECU combines that signal with vehicle speed, and sometimes steering angle, to decide the assist level. At parking speeds assist is high; at highway speeds it is reduced for stability. Because EPS typically runs on the 12 V system, low voltage or sensor faults can reduce assist and set warnings.
Question 9: A technician suspects an HV electric A/C compressor has an internal insulation fault. Which tool is appropriate to verify isolation between the HV terminals and the compressor housing, after the HV system is disabled?
- A standard digital multimeter on the volts range
- A test light
- An insulation resistance tester (megohmmeter) (Correct answer)
- A refrigerant manifold gauge set
Correct answer: An insulation resistance tester (megohmmeter)
An insulation tester applies a test voltage and measures very high resistances to confirm isolation. A standard multimeter cannot detect marginal insulation leakage.
HV components must be electrically isolated from the chassis, and breakdowns can be too small for a typical ohmmeter to detect. A megohmmeter applies a high test voltage and measures resistance, which reveals leakage paths. Always follow the manufacturer's procedure, including disabling the HV system, wearing rated PPE, and waiting for capacitor discharge. Compare readings with the specification; a low reading indicates the compressor should be replaced. A/C compressor insulation faults commonly set isolation DTCs.
Question 10: A hybrid is driven down a long hill immediately after a full charge, and the driver notices little regenerative braking. What is the most likely reason?
- The 12 V battery is overcharged
- The HV battery is at a high state of charge and cannot accept much charge (Correct answer)
- The friction brake pads are worn out
- The A/C compressor is blocking regeneration
Correct answer: The HV battery is at a high state of charge and cannot accept much charge
At high state of charge, the HV battery limits charge acceptance, so regenerative torque is reduced and friction brakes or engine braking take over. Cold temperature can have a similar limiting effect.
During regeneration, the motor-generator acts as a generator and sends current to the HV battery. The battery management system limits charging current based on state of charge, temperature, and cell health. When the battery is nearly full or very cold, the allowed regen power drops. The brake control system compensates by increasing hydraulic braking, and the driver may feel a change in deceleration. This is normal behavior and not a fault unless DTCs are set.
Question 11: Why can a typical hybrid's air conditioning continue to operate when the gasoline engine is stopped?
- The compressor is driven by the starter motor
- The compressor is driven by a belt connected to the transmission
- The system uses an absorption chiller instead of a compressor
- The compressor has its own HV-powered electric motor controlled through an inverter (Correct answer)
Correct answer: The compressor has its own HV-powered electric motor controlled through an inverter
Hybrid electric compressors run from the HV system, not from an engine belt. Their speed is controlled by an inverter commanded by the A/C ECU.
A hybrid with automatic engine stop cannot rely on a belt-driven compressor for cabin cooling. Instead, a scroll compressor with an integrated electric motor is powered from the HV battery. An inverter, often built into the compressor, adjusts its speed based on cooling demand. This also allows the compressor to cool the HV battery or cabin while the vehicle is stopped or charging. Because the compressor uses HV, service requires proper HV safety procedures and the specified insulating oil.
A technician is replacing the HV electric A/C compressor on a hybrid vehicle.
Which refrigerant oil must be used when servicing the system?
What Practice Test Geeks adds beyond an AI chat for ASE L3
An AI chatbot can quiz you, but it can't reproduce the exam conditions or keep your record. Here you get:
- A timed, full-length ASE L3 mock exam — 55 questions in 120 minutes with a 70% pass mark, modeled on the official exam's question count and time limit, followed by a score report broken down by exam domain.
- A fixed ASE L3 question bank: the same test every attempt, so your score is comparable from one try to the next instead of changing with every regenerated quiz.
- Progress saved on your device: completed tests, scores and missed questions stay in My Progress, so you can retake only what you got wrong.
- A printable ASE L3 cheat sheet you can print or save as a PDF.
- ASE L3 flashcards built from the same question bank.
These practice questions were written with AI tools. They are not real exam questions. Exam facts are checked against the official sources listed below. Not reviewed by a subject-matter expert. Editorial policy
Sources & references
Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy
- ase.com — Test delivery, registration deadline, test dates, eligibility, time limit, score validity · verified Nov 2026