← All SMS Flashcard Decks

Personal Protective Equipment (PPE) Flashcards

21 cards from real SMS practice questions. Tap to flip, then mark Knew It or Still Learning — missed cards come back until you master them.

Read the first 20 Personal Protective Equipment (PPE) flashcards as text
  1. According to OSHA 29 CFR 1910.132, who is responsible for conducting a workplace hazard assessment to determine necessary PPE?

    Answer: The employer

    OSHA 29 CFR 1910.132(d) places the responsibility on the employer to assess the workplace for hazards and determine what PPE is necessary.

  2. What is the correct hierarchy for controlling workplace hazards when determining whether PPE is needed?

    Answer: Elimination, Substitution, Engineering Controls, Administrative Controls, PPE

    The hierarchy of controls prioritizes elimination first, then substitution, engineering controls, administrative controls, and finally PPE as the last line of defense.

  3. Which ANSI standard governs the selection and use of eye and face protection in general industry?

    Answer: ANSI Z87.1

    ANSI Z87.1 is the standard for occupational and educational personal eye and face protection devices.

  4. When must an employer pay for employee PPE under OSHA regulations?

    Answer: For all PPE required by OSHA standards, with limited exceptions

    Under 29 CFR 1910.132(h), employers must pay for required PPE, except for non-specialty safety-toe footwear and non-specialty prescription safety eyewear that employees may use off the job.

  5. A safety manager discovers that employees are correctly wearing their respirators but complaining of headaches and fatigue. What is the most likely issue?

    Answer: Improper fit testing or an incorrect respirator type for the hazard

    Symptoms like headaches and fatigue while wearing respirators often indicate a poor face seal from improper fit testing or the wrong respirator type/cartridge for the contaminant present.

  6. Which class of hard hat is required when workers face exposure to high-voltage electrical conductors?

    Answer: Class B

    ANSI Z89.1 Class E (Electrical) hard hats, formerly Class B, are required for high-voltage protection and are tested up to 20,000 volts.

  7. What does a qualitative fit test (QLFT) assess for respirator users?

    Answer: Whether the wearer can detect a test agent through taste or smell, indicating a poor seal

    A qualitative fit test uses the wearer's sensory detection (taste, smell, or irritation) of a challenge agent to determine if the respirator seals adequately.

  8. Under OSHA 29 CFR 1910.134, what is the minimum frequency for fit testing employees who use tight-fitting respirators?

    Answer: Annually

    OSHA requires fit testing for tight-fitting respirators at least annually, and whenever there are changes that could affect the seal such as weight change or dental work.

  9. Which type of glove material provides the best protection against ketones and aromatic hydrocarbons?

    Answer: Butyl rubber

    Butyl rubber gloves offer superior resistance to ketones, esters, and aromatic hydrocarbons, making them the best choice for these specific chemical classes.

  10. A safety professional must select hearing protection for workers exposed to 98 dB(A) TWA noise. The selected earmuffs have an NRR of 26. What is the estimated protected exposure level using OSHA's derating method?

    Answer: 84 dB(A)

    OSHA derates NRR by 50%: (26 − 7) / 2 = 9.5 dB reduction; 98 − 9.5 = 88.5 ≈ 84 dB(A) after applying the correct derating formula (NRR-7)/2.

  11. What ANSI standard classification covers Type II hard hats, which provide additional protection from lateral impacts?

    Answer: ANSI Z89.1

    ANSI Z89.1 classifies hard hats by type (I or II) and class (G, E, C), with Type II providing top and lateral impact protection.

  12. When selecting chemical protective clothing (CPC), what document should a safety manager consult first to identify permeation resistance?

    Answer: The PPE manufacturer's chemical resistance chart

    The PPE manufacturer's chemical resistance or permeation data chart provides specific breakthrough time and permeation rate data for the glove or suit material against listed chemicals.

  13. Which OSHA standard requires employers to establish and maintain a written respiratory protection program when employees use respirators?

    Answer: 29 CFR 1910.134

    29 CFR 1910.134 specifically requires a written respiratory protection program covering procedures for selection, fit testing, medical evaluation, training, and maintenance.

  14. What is the primary purpose of a PPE hazard assessment certification document?

    Answer: To certify in writing that the workplace hazard assessment was performed and identifies the assessor and date

    OSHA 29 CFR 1910.132(d)(2) requires a written certification that identifies the workplace evaluated, the person certifying the assessment, and the date it was performed.

  15. An employer wants employees to use a supplied-air respirator (SAR) in an IDLH atmosphere. What additional requirement must be met beyond training and fit testing?

    Answer: A standby employee must be present and an escape respirator must be provided

    Per 29 CFR 1910.134(g)(3), when working in IDLH atmospheres, at least one standby employee must be located outside, and workers must have escape respirators available.

  16. Which of the following best describes the concept of 'assigned protection factor' (APF) for respirators?

    Answer: The expected workplace level of protection provided by a respirator class when used in a properly functioning program

    The APF represents the minimum anticipated level of protection provided by a properly functioning respirator class in a correctly implemented respiratory protection program.

  17. A safety manager is reviewing PPE for workers who handle concentrated sulfuric acid. What type of eye/face protection is most appropriate?

    Answer: Chemical splash goggles with indirect ventilation plus a face shield

    Concentrated sulfuric acid requires indirect-vent chemical splash goggles (to prevent splash ingress) combined with a face shield for complete face and neck protection.

  18. Which element is NOT typically required in a comprehensive written PPE program?

    Answer: Employee PPE personal preference survey results

    A written PPE program requires hazard assessment, selection criteria, training documentation, and maintenance procedures; employee preference surveys are not an OSHA program requirement.

  19. How should a safety manager handle PPE that has been contaminated with a hazardous chemical during an emergency?

    Answer: Follow the SDS guidance, quarantine the PPE, and dispose of or decontaminate per hazardous waste procedures

    Contaminated PPE must be handled according to SDS instructions, quarantined to prevent further exposure, and managed as potentially hazardous waste or properly decontaminated before reuse.

  20. What is the correct method for performing a negative pressure user seal check on a half-face air-purifying respirator?

    Answer: Block the inlet openings of cartridges and inhale gently so the facepiece collapses slightly and holds

    A negative pressure seal check is performed by blocking the inlet openings and inhaling gently; the facepiece should collapse slightly and remain collapsed for about 10 seconds, indicating no leakage.

Written and edited by , founder of Practice Test Geeks, with AI assistance. Exam facts are checked against the official sources linked below. Editorial policy

Sources & references

Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy

  1. bcsp.org — Test delivery, eligibility, registration, retake policy, score release, test dates, score validity, fees, renewal · verified Oct 2026