Rigging Licence Basic (RB) — CPCCLRG3001 — Questions and Answers

Question 1: What must a Crane Coordination procedure include to be effective?

Only a signature page
A brief paragraph
A company letterhead only
Clear steps, responsibilities, hazard controls, PPE requirements, emergency procedures, and review dates (Correct answer)

Correct answer: Clear steps, responsibilities, hazard controls, PPE requirements, emergency procedures, and review dates

Effective procedures must be comprehensive, clear, practical, and include all information needed for safe work.

Question 2: What is the importance of near-miss reporting for Rigging Hardware Maintenance?

They should only be discussed informally
Near misses are not important
They complicate record keeping
Near misses reveal existing hazards and allow preventive action before injuries occur (Correct answer)

Correct answer: Near misses reveal existing hazards and allow preventive action before injuries occur

Near misses are valuable indicators of hazards that could cause future injuries — reporting them enables preventive action.

Question 3: Under Australian regulations, who bears primary responsibility for Chain Slings and Fittings compliance?

The general public
Workers only
The PCBU (Person Conducting a Business or Undertaking) (Correct answer)
Equipment suppliers

Correct answer: The PCBU (Person Conducting a Business or Undertaking)

The PCBU has the primary duty under the WHS Act to ensure compliance with all safety requirements.

Question 4: How should WHS Legislation for Rigging equipment be inspected and maintained?

When someone remembers
Only when it breaks
Per manufacturer specifications and relevant Australian Standards, with documented inspection and maintenance records (Correct answer)
Only for new equipment

Correct answer: Per manufacturer specifications and relevant Australian Standards, with documented inspection and maintenance records

Equipment must be inspected and maintained according to specifications and standards, with all records documented.

Question 5: What is the significance of Australian Standards for Hazard Identification?

They are outdated
They are advisory only
Many are referenced in legislation making compliance legally required, and they set minimum technical requirements (Correct answer)
They only apply to imported products

Correct answer: Many are referenced in legislation making compliance legally required, and they set minimum technical requirements

Australian Standards referenced in WHS Regulations become legal requirements and set the minimum technical benchmarks for compliance.

Question 6: As the sling angle measured from vertical increases beyond 45 degrees when used with a spreader bar, what happens to the compressive force in the bar?

The compressive force increases significantly (Correct answer)
The compressive force remains constant regardless of sling angle
The compressive force decreases as the slings become more spread out
The compressive force reverses and becomes tensile

Correct answer: The compressive force increases significantly

As sling angles increase beyond 45° from vertical, the horizontal component of sling forces grows rapidly, driving up the compressive load on the spreader bar.

Question 7: Under Australian law, what rights do workers have regarding Emergency and Rescue Procedures safety?

Rights depend on seniority
No specific rights
Rights to information, training, consultation, representation through HSRs, and to cease unsafe work (Correct answer)
Only the right to complain

Correct answer: Rights to information, training, consultation, representation through HSRs, and to cease unsafe work

Workers have specific legal rights under WHS legislation including information, training, consultation, representation, and refusal of unsafe work.

Question 8: What supervisory requirements exist for Hazard Identification activities?

Only new workers need supervision
No supervision needed
Supervision is optional
Adequate supervision by competent persons, proportionate to the level of risk (Correct answer)

Correct answer: Adequate supervision by competent persons, proportionate to the level of risk

The level of supervision must be proportionate to the risk level, with competent supervisors overseeing the work.

Question 9: Which type of force does a spreader bar primarily experience during a lift?

Compression — because the sling legs push inward on both ends (Correct answer)
Bending — because the load hangs from its centre
Torsion — because the load rotates during the lift
Tension — because the slings pull it upward

Correct answer: Compression — because the sling legs push inward on both ends

Sling legs converge toward the crane hook, pushing inward on both ends of the spreader bar and placing it under compressive force.

Question 10: How should Crane Coordination incidents be reported in an Australian workplace?

Ignore minor incidents
Report immediately to the supervisor, with notifiable incidents reported to the regulator (Correct answer)
Post on social media
Wait until the weekly meeting

Correct answer: Report immediately to the supervisor, with notifiable incidents reported to the regulator

Incidents must be reported promptly, with notifiable incidents requiring immediate regulator notification.

Question 11: What supervisory requirements exist for Gin Poles and Derricks activities?

Adequate supervision by competent persons, proportionate to the level of risk (Correct answer)
Only new workers need supervision
Supervision is optional
No supervision needed

Correct answer: Adequate supervision by competent persons, proportionate to the level of risk

The level of supervision must be proportionate to the risk level, with competent supervisors overseeing the work.

Question 12: How should Crane Coordination risk controls be prioritised when multiple options exist?

Apply the hierarchy of controls — use the most effective control that is reasonably practicable (Correct answer)
Choose the cheapest option
Use all controls simultaneously regardless of cost
Let workers choose their preferred control

Correct answer: Apply the hierarchy of controls — use the most effective control that is reasonably practicable

The hierarchy of controls guides prioritisation — always implement the highest-level (most effective) control that is reasonably practicable.

Question 13: In Australian Australian rigging operations, what is the primary purpose of Rigging Principles and Theory procedures?

To satisfy insurance companies
To increase paperwork
To slow down operations
To protect worker health and safety through systematic hazard management (Correct answer)

Correct answer: To protect worker health and safety through systematic hazard management

Rigging Principles and Theory procedures are fundamental to protecting workers under Australian Australian rigging operations regulations.

Question 14: How does worker health monitoring relate to Rigging Hardware Maintenance?

Health monitoring can identify early signs of harm from ${subjectName} exposures, allowing intervention before serious injury (Correct answer)
It is not related
It is only for office workers
It is voluntarily only

Correct answer: Health monitoring can identify early signs of harm from ${subjectName} exposures, allowing intervention before serious injury

Health monitoring detects early signs of harm, enabling intervention before conditions become serious or irreversible.

Question 15: In Australian Australian rigging operations, what is the primary purpose of Load Calculations procedures?

To protect worker health and safety through systematic hazard management (Correct answer)
To satisfy insurance companies
To increase paperwork
To slow down operations

Correct answer: To protect worker health and safety through systematic hazard management

Load Calculations procedures are fundamental to protecting workers under Australian Australian rigging operations regulations.

Question 16: What is a Provisional Improvement Notice (PIN) in the context of Wire Rope Selection and Inspection?

A notice issued by a trained HSR requiring a contravention of WHS law to be remedied within a specified period (Correct answer)
A workplace award
A salary increment notice
A construction permit

Correct answer: A notice issued by a trained HSR requiring a contravention of WHS law to be remedied within a specified period

Trained HSRs can issue PINs when they believe a WHS contravention has occurred, requiring the PCBU to remedy the issue.

Question 17: What is the hierarchy of controls for managing WHS Legislation for Rigging risks?

Elimination, substitution, isolation, engineering, administrative, PPE — most to least effective (Correct answer)
PPE first, then other controls
Administrative controls only
No hierarchy exists

Correct answer: Elimination, substitution, isolation, engineering, administrative, PPE — most to least effective

The hierarchy ranks controls from most effective (elimination) to least effective (PPE), guiding risk control decisions.

Question 18: What is the significance of Australian Standards for Chain Slings and Fittings?

They are advisory only
They only apply to imported products
They are outdated
Many are referenced in legislation making compliance legally required, and they set minimum technical requirements (Correct answer)

Correct answer: Many are referenced in legislation making compliance legally required, and they set minimum technical requirements

Australian Standards referenced in WHS Regulations become legal requirements and set the minimum technical benchmarks for compliance.

Question 19: What must a Rigging Hardware Maintenance safety induction cover?

Company history only
Where to park
The company's financial performance
Specific hazards, safe work procedures, emergency arrangements, PPE requirements, and reporting procedures (Correct answer)

Correct answer: Specific hazards, safe work procedures, emergency arrangements, PPE requirements, and reporting procedures

Inductions must cover all information needed for workers to perform the activity safely.

Question 20: How often should Gin Poles and Derricks procedures be reviewed?

Every 20 years
Only when the regulator requests it
Regularly, after incidents, when conditions change, or when new information emerges (Correct answer)
Never once written

Correct answer: Regularly, after incidents, when conditions change, or when new information emerges

Procedures must be living documents, reviewed regularly and in response to changes, incidents, and new knowledge.

Question 21: What is the significance of Australian Standards for Crane Coordination?

They are outdated
They are advisory only
They only apply to imported products
Many are referenced in legislation making compliance legally required, and they set minimum technical requirements (Correct answer)

Correct answer: Many are referenced in legislation making compliance legally required, and they set minimum technical requirements

Australian Standards referenced in WHS Regulations become legal requirements and set the minimum technical benchmarks for compliance.

Question 22: When is it appropriate to use administrative controls for Gin Poles and Derricks risks?

As the first choice always
Never
When elimination, substitution, isolation, and engineering controls are not reasonably practicable (Correct answer)
Only on weekends

Correct answer: When elimination, substitution, isolation, and engineering controls are not reasonably practicable

Administrative controls (procedures, training, rotation) should be used when higher-level controls cannot adequately reduce the risk.

Question 23: What is the role of workplace safety committees in Crane Coordination management?

Planning social events
No role
Setting worker salaries
Facilitating cooperation between the PCBU and workers, reviewing safety procedures, and recommending improvements (Correct answer)

Correct answer: Facilitating cooperation between the PCBU and workers, reviewing safety procedures, and recommending improvements

Safety committees provide a structured forum for cooperation between management and workers on WHS matters.

Question 24: How often should Wire Rope Selection and Inspection procedures be reviewed?

Only when the regulator requests it
Never once written
Regularly, after incidents, when conditions change, or when new information emerges (Correct answer)
Every 20 years

Correct answer: Regularly, after incidents, when conditions change, or when new information emerges

Procedures must be living documents, reviewed regularly and in response to changes, incidents, and new knowledge.

Question 25: What is the hierarchy of controls for managing Chain Slings and Fittings risks?

No hierarchy exists
Elimination, substitution, isolation, engineering, administrative, PPE — most to least effective (Correct answer)
Administrative controls only
PPE first, then other controls

Correct answer: Elimination, substitution, isolation, engineering, administrative, PPE — most to least effective

The hierarchy ranks controls from most effective (elimination) to least effective (PPE), guiding risk control decisions.

Rigging Licence Basic (RB) — CPCCLRG3001

The Australian High Risk Work Licence for Basic Rigging (RB) tests knowledge and skills required to safely perform rigging operations including load calculations, sling selection, crane coordination, and steel erection under Work Health and Safety legislation.

Questions

30 min

Time Limit

70%

To Pass

Checking for saved progress...

Exam Rules

You can skip questions and return to them later
Flag questions for review before submitting
No feedback shown until you submit the entire exam
Unanswered questions count as wrong — answer everything
10 pretest questions are mixed in and don't affect your score
Timer auto-submits when time runs out
Your progress is auto-saved every 30 seconds