Rigging Licence Basic (RB) — CPCCLRG3001 — Questions and Answers

Question 1: How often should Crane Coordination procedures be reviewed?

Never once written
Only when the regulator requests it
Every 20 years
Regularly, after incidents, when conditions change, or when new information emerges (Correct answer)

Correct answer: Regularly, after incidents, when conditions change, or when new information emerges

Procedures must be living documents, reviewed regularly and in response to changes, incidents, and new knowledge.

Question 2: Under Australian law, what rights do workers have regarding Gin Poles and Derricks safety?

Rights to information, training, consultation, representation through HSRs, and to cease unsafe work (Correct answer)
Only the right to complain
Rights depend on seniority
No specific rights

Correct answer: Rights to information, training, consultation, representation through HSRs, and to cease unsafe work

Workers have specific legal rights under WHS legislation including information, training, consultation, representation, and refusal of unsafe work.

Question 3: What is the significance of Australian Standards for Load Calculations?

They are outdated
They only apply to imported products
They are advisory only
Many are referenced in legislation making compliance legally required, and they set minimum technical requirements (Correct answer)

Correct answer: Many are referenced in legislation making compliance legally required, and they set minimum technical requirements

Australian Standards referenced in WHS Regulations become legal requirements and set the minimum technical benchmarks for compliance.

Question 4: What is the consequence of inadequate Hazard Identification risk management?

Worker injuries, regulatory penalties, prosecution, compensation claims, and reputational damage (Correct answer)
Reduced paperwork
Minor inconvenience only
No consequences

Correct answer: Worker injuries, regulatory penalties, prosecution, compensation claims, and reputational damage

Inadequate risk management can result in injuries, deaths, regulatory enforcement, prosecution, civil claims, and significant reputational damage.

Question 5: What is a Provisional Improvement Notice (PIN) in the context of Wire Rope Selection and Inspection?

A workplace award
A notice issued by a trained HSR requiring a contravention of WHS law to be remedied within a specified period (Correct answer)
A construction permit
A salary increment notice

Correct answer: A notice issued by a trained HSR requiring a contravention of WHS law to be remedied within a specified period

Trained HSRs can issue PINs when they believe a WHS contravention has occurred, requiring the PCBU to remedy the issue.

Question 6: What is a Code of Practice relevant to Crane Coordination?

A practical guide approved under WHS legislation that can be used as evidence of what is reasonably practicable (Correct answer)
A voluntary suggestion only
A marketing document
A company internal policy

Correct answer: A practical guide approved under WHS legislation that can be used as evidence of what is reasonably practicable

Codes of Practice provide practical guidance with legal significance — they can be cited as evidence of what is known and reasonably practicable.

Question 7: What emergency procedures should cover Shackles and Hooks scenarios?

No emergency procedures needed
Only dialling 000
Response actions, evacuation, first aid, communication protocols, and specific hazard responses (Correct answer)
A general evacuation plan only

Correct answer: Response actions, evacuation, first aid, communication protocols, and specific hazard responses

Emergency procedures must be comprehensive and specific to the hazards associated with the activity.

Question 8: How should new Rigging Hardware Maintenance risks be incorporated into existing safety systems?

Wait for the next scheduled review
File them for future reference
Ignore them
Through review and update of risk assessments, procedures, training, and communication to all affected workers (Correct answer)

Correct answer: Through review and update of risk assessments, procedures, training, and communication to all affected workers

New risks must be promptly incorporated into risk assessments, procedures, and communicated to all affected workers.

Question 9: What training is required before workers perform Crane Coordination activities?

No training — learn on the job
A quick verbal briefing only
Appropriate training covering hazards, procedures, equipment use, and emergency response (Correct answer)
Self-study from a pamphlet

Correct answer: Appropriate training covering hazards, procedures, equipment use, and emergency response

Workers must receive comprehensive training appropriate to the risks before performing the activity.

Question 10: What supervisory requirements exist for Emergency and Rescue Procedures activities?

Adequate supervision by competent persons, proportionate to the level of risk (Correct answer)
Supervision is optional
No supervision needed
Only new workers need supervision

Correct answer: Adequate supervision by competent persons, proportionate to the level of risk

The level of supervision must be proportionate to the risk level, with competent supervisors overseeing the work.

Question 11: How should new Hazard Identification risks be incorporated into existing safety systems?

Through review and update of risk assessments, procedures, training, and communication to all affected workers (Correct answer)
File them for future reference
Ignore them
Wait for the next scheduled review

Correct answer: Through review and update of risk assessments, procedures, training, and communication to all affected workers

New risks must be promptly incorporated into risk assessments, procedures, and communicated to all affected workers.

Question 12: In Australian Australian rigging operations, what is the primary purpose of Crane Coordination procedures?

To protect worker health and safety through systematic hazard management (Correct answer)
To slow down operations
To increase paperwork
To satisfy insurance companies

Correct answer: To protect worker health and safety through systematic hazard management

Crane Coordination procedures are fundamental to protecting workers under Australian Australian rigging operations regulations.

Question 13: What must a Wire Rope Selection and Inspection procedure include to be effective?

A company letterhead only
Only a signature page
A brief paragraph
Clear steps, responsibilities, hazard controls, PPE requirements, emergency procedures, and review dates (Correct answer)

Correct answer: Clear steps, responsibilities, hazard controls, PPE requirements, emergency procedures, and review dates

Effective procedures must be comprehensive, clear, practical, and include all information needed for safe work.

Question 14: How should Crane Coordination incidents be reported in an Australian workplace?

Ignore minor incidents
Post on social media
Report immediately to the supervisor, with notifiable incidents reported to the regulator (Correct answer)
Wait until the weekly meeting

Correct answer: Report immediately to the supervisor, with notifiable incidents reported to the regulator

Incidents must be reported promptly, with notifiable incidents requiring immediate regulator notification.

Question 15: What record retention period applies to Hazard Identification documents under WHS Regulations?

Until the end of the project
No retention required
Typically 5 years, or 30 years for health monitoring and asbestos records (Correct answer)
1 month

Correct answer: Typically 5 years, or 30 years for health monitoring and asbestos records

Most WHS records must be kept for 5 years, with longer periods for specific records such as health monitoring (30 years) and asbestos.

Question 16: What is the role of workplace safety committees in Steel Erection Basics management?

Facilitating cooperation between the PCBU and workers, reviewing safety procedures, and recommending improvements (Correct answer)
No role
Planning social events
Setting worker salaries

Correct answer: Facilitating cooperation between the PCBU and workers, reviewing safety procedures, and recommending improvements

Safety committees provide a structured forum for cooperation between management and workers on WHS matters.

Question 17: How should new Emergency and Rescue Procedures risks be incorporated into existing safety systems?

Ignore them
Through review and update of risk assessments, procedures, training, and communication to all affected workers (Correct answer)
Wait for the next scheduled review
File them for future reference

Correct answer: Through review and update of risk assessments, procedures, training, and communication to all affected workers

New risks must be promptly incorporated into risk assessments, procedures, and communicated to all affected workers.

Question 18: How should Emergency and Rescue Procedures incidents be reported in an Australian workplace?

Report immediately to the supervisor, with notifiable incidents reported to the regulator (Correct answer)
Ignore minor incidents
Wait until the weekly meeting
Post on social media

Correct answer: Report immediately to the supervisor, with notifiable incidents reported to the regulator

Incidents must be reported promptly, with notifiable incidents requiring immediate regulator notification.

Question 19: How should new Wire Rope Selection and Inspection risks be incorporated into existing safety systems?

File them for future reference
Through review and update of risk assessments, procedures, training, and communication to all affected workers (Correct answer)
Ignore them
Wait for the next scheduled review

Correct answer: Through review and update of risk assessments, procedures, training, and communication to all affected workers

New risks must be promptly incorporated into risk assessments, procedures, and communicated to all affected workers.

Question 20: After completing a rigging operation using a spreader bar, what is the correct post-use procedure?

Return the spreader bar to the crane operator's cabin for storage
Leave the spreader bar rigged ready for the next lift to save time
Submit the bar for immediate recertification after every single use
Clean the bar, inspect it for damage, and store it correctly in a designated area (Correct answer)

Correct answer: Clean the bar, inspect it for damage, and store it correctly in a designated area

Post-use care — cleaning, inspecting for damage, and correct storage — maintains equipment condition, ensures readiness for future lifts, and ensures any damage is identified promptly.

Question 21: What is the importance of near-miss reporting for Crane Coordination?

Near misses are not important
They complicate record keeping
They should only be discussed informally
Near misses reveal existing hazards and allow preventive action before injuries occur (Correct answer)

Correct answer: Near misses reveal existing hazards and allow preventive action before injuries occur

Near misses are valuable indicators of hazards that could cause future injuries — reporting them enables preventive action.

Question 22: What is a Provisional Improvement Notice (PIN) in the context of Crane Coordination?

A construction permit
A workplace award
A salary increment notice
A notice issued by a trained HSR requiring a contravention of WHS law to be remedied within a specified period (Correct answer)

Correct answer: A notice issued by a trained HSR requiring a contravention of WHS law to be remedied within a specified period

Trained HSRs can issue PINs when they believe a WHS contravention has occurred, requiring the PCBU to remedy the issue.

Question 23: Under Australian law, what rights do workers have regarding Wire Rope Selection and Inspection safety?

No specific rights
Rights depend on seniority
Rights to information, training, consultation, representation through HSRs, and to cease unsafe work (Correct answer)
Only the right to complain

Correct answer: Rights to information, training, consultation, representation through HSRs, and to cease unsafe work

Workers have specific legal rights under WHS legislation including information, training, consultation, representation, and refusal of unsafe work.

Question 24: What penalties apply for non-compliance with Chain Slings and Fittings regulations in Australia?

A verbal warning only
No penalties
A small administrative fee
Significant fines (up to millions of AUD for corporations) and potential imprisonment for serious offences (Correct answer)

Correct answer: Significant fines (up to millions of AUD for corporations) and potential imprisonment for serious offences

Australian WHS penalties are severe, with Category 1 offences carrying fines up to AUD 3 million and potential imprisonment.

Question 25: What is continuous improvement in Wire Rope Selection and Inspection management?

Increasing work speed each quarter
Cutting safety budgets annually
Systematically reviewing performance, learning from incidents, and implementing improvements to prevent future harm (Correct answer)
Doing the same thing year after year

Correct answer: Systematically reviewing performance, learning from incidents, and implementing improvements to prevent future harm

Continuous improvement involves ongoing evaluation and enhancement of safety practices based on monitoring, audits, incidents, and feedback.

Question 26: What is a Code of Practice relevant to Wire Rope Selection and Inspection?

A practical guide approved under WHS legislation that can be used as evidence of what is reasonably practicable (Correct answer)
A voluntary suggestion only
A marketing document
A company internal policy

Correct answer: A practical guide approved under WHS legislation that can be used as evidence of what is reasonably practicable

Codes of Practice provide practical guidance with legal significance — they can be cited as evidence of what is known and reasonably practicable.

Question 27: What is a Provisional Improvement Notice (PIN) in the context of WHS Legislation for Rigging?

A salary increment notice
A workplace award
A construction permit
A notice issued by a trained HSR requiring a contravention of WHS law to be remedied within a specified period (Correct answer)

Correct answer: A notice issued by a trained HSR requiring a contravention of WHS law to be remedied within a specified period

Trained HSRs can issue PINs when they believe a WHS contravention has occurred, requiring the PCBU to remedy the issue.

Question 28: How should Wire Rope Selection and Inspection hazards be communicated to workers?

They should not be communicated
By word of mouth only
Through inductions, toolbox talks, signage, labels, SDSs, and written procedures before exposure (Correct answer)
Through an annual newsletter

Correct answer: Through inductions, toolbox talks, signage, labels, SDSs, and written procedures before exposure

Hazard communication must use multiple channels and occur before workers are exposed to the hazards.

Question 29: What is the purpose of monitoring and reviewing WHS Legislation for Rigging controls?

To verify controls remain effective, identify new hazards, and drive continuous improvement (Correct answer)
To keep workers busy
To create busywork
To justify the safety budget

Correct answer: To verify controls remain effective, identify new hazards, and drive continuous improvement

Monitoring and review ensures controls continue to work as intended and identifies any emerging hazards or improvement opportunities.

Question 30: How should Emergency and Rescue Procedures hazards be communicated to workers?

By word of mouth only
Through an annual newsletter
They should not be communicated
Through inductions, toolbox talks, signage, labels, SDSs, and written procedures before exposure (Correct answer)

Correct answer: Through inductions, toolbox talks, signage, labels, SDSs, and written procedures before exposure

Hazard communication must use multiple channels and occur before workers are exposed to the hazards.

Question 31: What is the hierarchy of controls for managing Rigging Principles and Theory risks?

PPE first, then other controls
No hierarchy exists
Elimination, substitution, isolation, engineering, administrative, PPE — most to least effective (Correct answer)
Administrative controls only

Correct answer: Elimination, substitution, isolation, engineering, administrative, PPE — most to least effective

The hierarchy ranks controls from most effective (elimination) to least effective (PPE), guiding risk control decisions.

Question 32: In Australian Australian rigging operations, what is the primary purpose of Rigging Hardware Maintenance procedures?

To increase paperwork
To protect worker health and safety through systematic hazard management (Correct answer)
To satisfy insurance companies
To slow down operations

Correct answer: To protect worker health and safety through systematic hazard management

Rigging Hardware Maintenance procedures are fundamental to protecting workers under Australian Australian rigging operations regulations.

Question 33: A spreader bar is rated at 4.0 tonnes SWL. Due to the sling configuration, a deration factor of 0.75 applies. What is the maximum load that can safely be lifted?

4.0 tonnes
2.0 tonnes
5.3 tonnes
3.0 tonnes (Correct answer)

Correct answer: 3.0 tonnes

Applying the deration factor: 4.0t × 0.75 = 3.0 tonnes is the maximum allowable lift weight under these sling conditions.

Question 34: What obligation does a worker have if they identify a Load Calculations hazard?

Fix it themselves without telling anyone
Document it in their personal diary only
Report it immediately to their supervisor or HSR, and take reasonable care to protect themselves and others (Correct answer)
No obligation

Correct answer: Report it immediately to their supervisor or HSR, and take reasonable care to protect themselves and others

Workers have a legal obligation to report hazards and take reasonable care for their own and others' health and safety.

Question 35: What emergency procedures should cover Gin Poles and Derricks scenarios?

Response actions, evacuation, first aid, communication protocols, and specific hazard responses (Correct answer)
A general evacuation plan only
Only dialling 000
No emergency procedures needed

Correct answer: Response actions, evacuation, first aid, communication protocols, and specific hazard responses

Emergency procedures must be comprehensive and specific to the hazards associated with the activity.

Question 36: How should Wire Rope Selection and Inspection incidents be reported in an Australian workplace?

Wait until the weekly meeting
Post on social media
Ignore minor incidents
Report immediately to the supervisor, with notifiable incidents reported to the regulator (Correct answer)

Correct answer: Report immediately to the supervisor, with notifiable incidents reported to the regulator

Incidents must be reported promptly, with notifiable incidents requiring immediate regulator notification.

Question 37: What is the importance of near-miss reporting for Gin Poles and Derricks?

They complicate record keeping
Near misses reveal existing hazards and allow preventive action before injuries occur (Correct answer)
Near misses are not important
They should only be discussed informally

Correct answer: Near misses reveal existing hazards and allow preventive action before injuries occur

Near misses are valuable indicators of hazards that could cause future injuries — reporting them enables preventive action.

Question 38: What supervisory requirements exist for Steel Erection Basics activities?

No supervision needed
Only new workers need supervision
Supervision is optional
Adequate supervision by competent persons, proportionate to the level of risk (Correct answer)

Correct answer: Adequate supervision by competent persons, proportionate to the level of risk

The level of supervision must be proportionate to the risk level, with competent supervisors overseeing the work.

Question 39: How should Crane Coordination equipment be inspected and maintained?

When someone remembers
Only when it breaks
Only for new equipment
Per manufacturer specifications and relevant Australian Standards, with documented inspection and maintenance records (Correct answer)

Correct answer: Per manufacturer specifications and relevant Australian Standards, with documented inspection and maintenance records

Equipment must be inspected and maintained according to specifications and standards, with all records documented.

Question 40: What must be done when Chain Slings and Fittings legislation changes?

Wait to see if the changes are enforced
Only update paperwork when audited
Nothing — old rules still apply
Update procedures, risk assessments, and training to comply with the new requirements (Correct answer)

Correct answer: Update procedures, risk assessments, and training to comply with the new requirements

Legislative changes must be promptly reflected in procedures, risk assessments, and training to maintain compliance.

Question 41: When is it appropriate to use administrative controls for Chain Slings and Fittings risks?

Never
Only on weekends
As the first choice always
When elimination, substitution, isolation, and engineering controls are not reasonably practicable (Correct answer)

Correct answer: When elimination, substitution, isolation, and engineering controls are not reasonably practicable

Administrative controls (procedures, training, rotation) should be used when higher-level controls cannot adequately reduce the risk.

Question 42: What documentation must be maintained for Crane Coordination activities?

A brief email
No documentation needed
Only financial records
Risk assessments, training records, incident reports, and inspection logs as required by WHS Regulations (Correct answer)

Correct answer: Risk assessments, training records, incident reports, and inspection logs as required by WHS Regulations

WHS Regulations require maintaining various records for compliance, auditing, and incident investigation purposes.

Question 43: What is a Code of Practice relevant to Load Calculations?

A company internal policy
A practical guide approved under WHS legislation that can be used as evidence of what is reasonably practicable (Correct answer)
A marketing document
A voluntary suggestion only

Correct answer: A practical guide approved under WHS legislation that can be used as evidence of what is reasonably practicable

Codes of Practice provide practical guidance with legal significance — they can be cited as evidence of what is known and reasonably practicable.

Question 44: What penalties apply for non-compliance with Load Calculations regulations in Australia?

A small administrative fee
A verbal warning only
Significant fines (up to millions of AUD for corporations) and potential imprisonment for serious offences (Correct answer)
No penalties

Correct answer: Significant fines (up to millions of AUD for corporations) and potential imprisonment for serious offences

Australian WHS penalties are severe, with Category 1 offences carrying fines up to AUD 3 million and potential imprisonment.

Question 45: What is the role of a WHS inspector regarding Gin Poles and Derricks compliance?

To manage the project
To do the work themselves
To provide insurance
To monitor compliance, investigate incidents, provide guidance, and issue improvement or prohibition notices (Correct answer)

Correct answer: To monitor compliance, investigate incidents, provide guidance, and issue improvement or prohibition notices

WHS inspectors enforce legislation through monitoring, investigation, guidance, and enforcement notices.

Question 46: How does worker health monitoring relate to Crane Coordination?

It is voluntarily only
It is only for office workers
Health monitoring can identify early signs of harm from ${subjectName} exposures, allowing intervention before serious injury (Correct answer)
It is not related

Correct answer: Health monitoring can identify early signs of harm from ${subjectName} exposures, allowing intervention before serious injury

Health monitoring detects early signs of harm, enabling intervention before conditions become serious or irreversible.

Question 47: How should Chain Slings and Fittings incidents be reported in an Australian workplace?

Post on social media
Ignore minor incidents
Wait until the weekly meeting
Report immediately to the supervisor, with notifiable incidents reported to the regulator (Correct answer)

Correct answer: Report immediately to the supervisor, with notifiable incidents reported to the regulator

Incidents must be reported promptly, with notifiable incidents requiring immediate regulator notification.

Question 48: What supervisory requirements exist for Wire Rope Selection and Inspection activities?

Supervision is optional
Adequate supervision by competent persons, proportionate to the level of risk (Correct answer)
No supervision needed
Only new workers need supervision

Correct answer: Adequate supervision by competent persons, proportionate to the level of risk

The level of supervision must be proportionate to the risk level, with competent supervisors overseeing the work.

Question 49: What must a Gin Poles and Derricks procedure include to be effective?

Clear steps, responsibilities, hazard controls, PPE requirements, emergency procedures, and review dates (Correct answer)
Only a signature page
A brief paragraph
A company letterhead only

Correct answer: Clear steps, responsibilities, hazard controls, PPE requirements, emergency procedures, and review dates

Effective procedures must be comprehensive, clear, practical, and include all information needed for safe work.

Question 50: What record retention period applies to Gin Poles and Derricks documents under WHS Regulations?

1 month
Typically 5 years, or 30 years for health monitoring and asbestos records (Correct answer)
No retention required
Until the end of the project

Correct answer: Typically 5 years, or 30 years for health monitoring and asbestos records

Most WHS records must be kept for 5 years, with longer periods for specific records such as health monitoring (30 years) and asbestos.

Rigging Licence Basic (RB) — CPCCLRG3001

The Australian High Risk Work Licence for Basic Rigging (RB) tests knowledge and skills required to safely perform rigging operations including load calculations, sling selection, crane coordination, and steel erection under Work Health and Safety legislation.

Questions

60 min

Time Limit

70%

To Pass

Checking for saved progress...

Exam Rules

You can skip questions and return to them later
Flag questions for review before submitting
No feedback shown until you submit the entire exam
Unanswered questions count as wrong — answer everything
10 pretest questions are mixed in and don't affect your score
Timer auto-submits when time runs out
Your progress is auto-saved every 30 seconds

These practice questions were written with AI tools. They are not real exam questions. Exam facts are checked against the official sources listed below. Not reviewed by a subject-matter expert. Editorial policy

Sources & references

Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy

worksafe.vic.gov.au — Fees, registration deadline, renewal, score release · verified Oct 2026
safework.nsw.gov.au — Eligibility, registration deadline, retake policy, score validity · verified Oct 2026
wa.gov.au — Fees, renewal · verified Oct 2026
worksafe.qld.gov.au — Fees, renewal · verified Oct 2026
training.gov.au — Test delivery, eligibility · verified Oct 2026