← All 456A Flashcard Decks

Weld Quality Inspection, Testing & Occupational Safety Flashcards

6 cards from real 456A practice questions. Tap to flip, then mark Knew It or Still Learning — missed cards come back until you master them.

Read the first 6 Weld Quality Inspection, Testing & Occupational Safety flashcards as text
  1. What is the primary difference between a 'destructive test' and a 'non-destructive test' (NDT) in weld inspection?

    Answer: Destructive tests destroy the test coupon/weld to measure properties; NDT examines the weld without destroying it, allowing the tested component to remain in service

    Destructive tests (tensile, bend, impact, macro, hardness) provide quantitative data on mechanical properties but consume the test specimen. NDT (visual, RT, UT, MT, PT, ET) examines the weld without destroying it, allowing the production component to remain in service. Qualification testing uses both; production inspection relies on NDT.

  2. What does 'visual inspection' (VT) detect in welds and what tools are used per CSA W59?

    Answer: Surface discontinuities including cracks, undercut, overlap, surface porosity, crater fill, weld profile/size, and weld length; tools include weld gauges, magnifying lens, fillet gauges, and adequate lighting

    Visual inspection is the most fundamental and first NDT method applied to all welds. Qualified visual inspection per CSA W59 detects: cracks, undercut, overlap, surface porosity, crater fill adequacy, weld reinforcement/profile, weld size (leg and throat), length, and location. Tools include calibrated weld gauges (HI-LO gauges, fillet weld gauges, pit gauges), magnifying glass (up to 10×), adequate lighting (minimum 500 lux), and mirrors for access.

  3. What is 'radiographic testing' (RT) of welds and what type of defects is it most sensitive to?

    Answer: X-ray or gamma-ray imaging of the weld; most sensitive to volumetric discontinuities — porosity, slag inclusions, burn-through, incomplete penetration

    Radiographic testing uses ionizing radiation (X-rays or Ir-192/Se-75 gamma sources) that passes through the weld and exposes film or a digital detector. Denser material absorbs more radiation; discontinuities show as darker areas on the radiograph. RT is most sensitive to volumetric defects (pores, inclusions) aligned with the radiation beam. It provides a permanent record (film) but requires radiation safety procedures under CNSC regulations in Canada.

  4. What is 'ultrasonic testing' (UT) and what type of weld defects is it best suited to detect compared to RT?

    Answer: Uses high-frequency sound waves; best suited to planar defects (cracks, LOF, LOP) that are poorly detected by RT due to orientation

    UT uses piezoelectric transducers to send high-frequency sound waves through the weld. Discontinuities reflect sound back to the transducer (pulse-echo method), indicating location, depth, and size. UT is superior to RT for planar defects (cracks, LOF, LOP) oriented perpendicular to the sound beam because RT cannot reliably detect narrow planar defects. Phased array UT (PAUT) provides enhanced visualization and is increasingly specified in Canadian pipeline and structural codes.

  5. What is 'magnetic particle testing' (MT) and on which base metals can it be used?

    Answer: Uses magnetic fields and iron particle indicators to reveal surface and near-surface discontinuities; can only be used on ferromagnetic materials (carbon steel, low-alloy steel)

    MT applies a magnetic field to the workpiece and then applies magnetic particles (dry powder or wet fluorescent solution). Leakage flux at surface or near-surface discontinuities attracts the particles, creating a visible indication. MT is limited to ferromagnetic materials (iron, nickel, cobalt-based). Austenitic stainless steel and aluminum are non-ferromagnetic and cannot be inspected by MT — PT (dye penetrant) is used instead.

  6. What is 'dye penetrant testing' (PT) and what is the correct sequence of steps?

    Answer: Apply penetrant → dwell → remove excess → apply developer → inspect → post-clean; detects surface-breaking discontinuities in any non-porous material

    The correct PT sequence is: (1) pre-clean and dry the surface; (2) apply liquid penetrant; (3) allow dwell time (typically 5–20 min) for the penetrant to seep into discontinuities; (4) remove excess penetrant; (5) apply developer to draw penetrant back to the surface and amplify indication; (6) inspect under adequate light; (7) post-clean the surface. PT detects surface-breaking cracks, pores, and LOF on any non-porous material regardless of ferromagnetism.

How this page was made: written with AI tools and published by Nathan Beja, founder of Practice Test Geeks, who is responsible for its content. Exam facts are checked against the official sources listed below. Not reviewed by a subject-matter expert. Editorial policy

Sources & references

Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy

  1. red-seal.ca — Exam format, exam information · verified Nov 2026
  2. skilledtradesontario.ca — Passing score, score release, time limit, renewal, score validity, eligibility, retake fee, test delivery, fees, retake policy · verified Nov 2026