← All 456A Flashcard Decks

Weld Quality Inspection, Testing & Occupational Safety Flashcards

6 cards from real 456A practice questions. Tap to flip, then mark Knew It or Still Learning — missed cards come back until you master them.

Read the first 6 Weld Quality Inspection, Testing & Occupational Safety flashcards as text
  1. What is 'manganese toxicity' in welding fume and why is it a significant concern for Canadian welders?

    Answer: Inhaled manganese from welding fume deposits in the brain, causing manganism (a Parkinson-like neurological disorder); significant because manganese is present in virtually all carbon and stainless steel fumes

    Manganese is a neurotoxin that accumulates in the basal ganglia of the brain, causing manganism with symptoms resembling Parkinson's disease (tremor, rigidity, impaired coordination). The ACGIH TLV-TWA for manganese is 0.02 mg/m³ — 50 times lower than the general welding fume OEL — reflecting its high toxicity. Since all carbon steels and stainless steels contain manganese (0.4–2%), all welding fume contains manganese.

  2. What is 'hexavalent chromium' (Cr(VI)) in welding fume and which type of welding generates the most?

    Answer: A highly toxic, carcinogenic oxidation state of chromium; generated in highest concentrations when welding stainless steel, chrome-moly, and chromium-containing alloys

    Hexavalent chromium Cr(VI) is classified as a human carcinogen (IARC Group 1) and is produced when chromium-containing steels are welded. The highest Cr(VI) fume concentrations occur with stainless steel SMAW (E308/309 flux coatings produce more Cr(VI) than GMAW or GTAW). The ACGIH TLV-TWA for Cr(VI) is 0.01 mg/m³, requiring high-efficiency local exhaust ventilation or respiratory protection.

  3. What does 'eye strain' from arc welding radiation mean and what is the proper term for the condition caused by UV exposure to unprotected eyes?

    Answer: Photokeratitis (welder's flash / arc eye) — UV radiation causes painful inflammation of the cornea; symptoms appear 6–12 hours after exposure and include intense eye pain, sensitivity to light, and the sensation of sand in the eyes

    Photokeratitis (arc eye, flash burn, welder's flash) is caused by UV radiation exposure to unprotected eyes. The corneal cells are burned, causing symptoms that typically appear 6–12 hours after exposure: severe eye pain, photophobia (light sensitivity), tearing, and the sensation of sand in the eyes. While usually self-limiting (heals in 24–48 hours with rest and eye drops), repeated exposures can cause long-term damage. All workers within view of the arc must be protected.

  4. What special precautions are required before welding or cutting on containers that previously held flammable materials, per CSA W117.2?

    Answer: Clean and purge thoroughly; test with a combustible gas detector to confirm LEL is below 10%; or fill with water or inert gas before cutting; never use compressed air to check — it may create an explosive atmosphere

    Welding on containers that held flammable substances (tanks, drums, pipes) is one of the most common causes of welding-related fatalities in Canada. CSA W117.2 and the NFC require: thorough cleaning (steam cleaning, chemical purging); atmospheric testing with a calibrated combustible gas detector; and continuous monitoring during work. The 'double purge' method (clean with water, then purge with nitrogen or CO2) is the safest approach. 'Empty' containers can still contain explosive residue.

  5. What is 'grounding' (workpiece connection) in SMAW welding and why is it critical for electrical safety?

    Answer: The welding circuit return connection from the workpiece to the welding machine; it must be attached to or as close as possible to the work to prevent stray current from flowing through unintended paths such as pipelines or structural steel

    The 'work lead' (commonly but incorrectly called the ground cable) completes the welding circuit from the workpiece back to the power source. It must be attached close to the weld to minimize the resistance and length of the current path through the workpiece. Improper work lead placement causes stray current to flow through adjacent structures, pipelines, or equipment, causing arc burns at contact points, corrosion of metallic structures, and potential electrocution hazards.

  6. Under Canadian OHS regulations, what is required when welding produces noise levels above 85 dBA in the workplace?

    Answer: Implementation of a hearing conservation program including: engineering noise controls, worker noise exposure assessment, provision of hearing protection (minimum SNR to reduce exposure to 85 dBA or below), and audiometric testing

    Canadian OHS regulations (federal and provincial) set action levels at 85 dBA TWA8 and a 3-dB exchange rate. Above 85 dBA, employers must: assess exposures, implement engineering noise controls (barriers, isolation), provide appropriate hearing protection (plugs or muffs with adequate NRR), and implement an audiometric testing program. Welding processes vary widely in noise generation: SMAW and GTAW are relatively quiet; air carbon arc gouging and plasma cutting produce very high noise levels.

How this page was made: written with AI tools and published by Nathan Beja, founder of Practice Test Geeks, who is responsible for its content. Exam facts are checked against the official sources listed below. Not reviewed by a subject-matter expert. Editorial policy

Sources & references

Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy

  1. red-seal.ca — Exam format, exam information · verified Nov 2026
  2. skilledtradesontario.ca — Passing score, score release, time limit, renewal, score validity, eligibility, retake fee, test delivery, fees, retake policy · verified Nov 2026