← All 456A Flashcard Decks

Weld Quality Control Flashcards

6 cards from real 456A practice questions. Tap to flip, then mark Knew It or Still Learning — missed cards come back until you master them.

Read the first 6 Weld Quality Control flashcards as text
  1. What is the difference between a weld discontinuity and a weld defect?

    Answer: A discontinuity is any interruption in the normal weld structure; it becomes a defect only when it exceeds the acceptance criteria specified by the applicable code or standard

    A discontinuity is any interruption in the typical structure of a weld (porosity, undercut, crack, inclusion, etc.). Not all discontinuities are defects. A discontinuity becomes a defect only when its size, type, or location exceeds the acceptance criteria of the governing code or standard (e.g., CSA W59, AWS D1.1).

  2. What is visual inspection (VT) and why is it the most important NDE method?

    Answer: A systematic examination of welds before, during, and after welding using the unaided eye or visual aids; important because it is the first line of quality control and can prevent defects rather than just finding them

    Visual inspection is the systematic examination of weld quality at all stages: before welding (fit-up, cleanliness, preheat), during welding (interpass temperature, technique, interpass cleaning), and after welding (size, profile, surface discontinuities). It is the most important NDE method because it can prevent defects and is required on every weld.

  3. What does radiographic testing (RT) detect in welds?

    Answer: Subsurface (internal) discontinuities such as porosity, slag inclusions, lack of fusion, incomplete penetration, and cracks by passing X-rays or gamma rays through the weld

    Radiographic testing uses X-rays or gamma rays to create an image (film or digital) of the internal weld structure. It detects subsurface discontinuities including porosity, slag inclusions, lack of fusion, incomplete penetration, and cracks. It provides a permanent record (the radiograph) but requires radiation safety precautions and trained, certified interpreters.

  4. What is a Welding Procedure Specification (WPS) and why is it required?

    Answer: A written document specifying all essential variables for a specific weld (process, filler metal, preheat, interpass temperature, technique, etc.) — required to ensure consistent, code-compliant welds

    A WPS is a written, qualified document that details all essential variables for producing a specific weld: welding process, base metal, filler metal type and size, shielding gas, preheat and interpass temperatures, polarity, amperage and voltage ranges, travel speed, joint design, and technique. Under CSA W47.1, all structural welds must be made to a qualified WPS.

  5. What is the purpose of preheat in welding and when is it required?

    Answer: To slow the cooling rate of the weld and HAZ, reducing the risk of hydrogen-induced cracking, reducing residual stresses, and improving fusion in thick or high-carbon/alloy steels

    Preheat slows the cooling rate after welding, which: (1) reduces the risk of hydrogen-induced cracking by allowing hydrogen to diffuse out, (2) reduces hardness in the heat-affected zone (HAZ), (3) reduces residual stresses and distortion, and (4) improves wetting and fusion. CSA W59 specifies minimum preheat temperatures based on material thickness, grade, and hydrogen level.

  6. What is the purpose of a bend test in weld qualification?

    Answer: To evaluate weld ductility, fusion, and soundness by bending a specimen to a specified radius and examining the outer surface for cracks or discontinuities exceeding the acceptance criteria

    Guided bend tests evaluate weld quality by plastically deforming a specimen cut from a test weld. The convex (outer) surface is examined for cracks, lack of fusion, and other discontinuities. Face bends test the weld face side, root bends test the root side, and side bends test the cross-section. Under CSA W47.1, bend tests are part of welder qualification testing.

How this page was made: written with AI tools and published by Nathan Beja, founder of Practice Test Geeks, who is responsible for its content. Exam facts are checked against the official sources listed below. Not reviewed by a subject-matter expert. Editorial policy

Sources & references

Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy

  1. red-seal.ca — Exam format, exam information · verified Nov 2026
  2. skilledtradesontario.ca — Passing score, score release, time limit, renewal, score validity, eligibility, retake fee, test delivery, fees, retake policy · verified Nov 2026