← All 456A Flashcard Decks

TIG (GTAW - Gas Tungsten Arc Welding) Flashcards

6 cards from real 456A practice questions. Tap to flip, then mark Knew It or Still Learning — missed cards come back until you master them.

Read the first 6 TIG (GTAW - Gas Tungsten Arc Welding) flashcards as text
  1. What is 'cold wire' vs. 'hot wire' addition in orbital GTAW and when is hot wire preferred?

    Answer: Cold wire is fed at room temperature; hot wire is resistance-preheated; hot wire is preferred for thick-wall pipe to increase deposition rate

    In cold wire orbital GTAW, filler is fed at ambient temperature. In hot wire, the filler wire is resistance-heated to near melting point before entering the arc, increasing deposition rate significantly. Hot wire is preferred for thick-wall pipe (schedule 80 and above) where multiple fill passes are required and productivity is critical, such as power generation or offshore piping.

  2. What is the 'heat input' formula used in GTAW welding procedure qualification?

    Answer: HI = (Amps × Volts × 60) / (Travel Speed in mm/min) = J/mm

    Heat input (HI) in J/mm = (Amps × Volts × 60) ÷ Travel Speed (mm/min). This formula calculates the energy deposited per unit length of weld. Controlling heat input is critical for maintaining mechanical properties (especially toughness) in the HAZ, especially for fine-grained steels and austenitic stainless steels where excessive heat causes grain growth and sensitization.

  3. What is a 'Procedure Qualification Record' (PQR) and how does it relate to a WPS under CSA W47.1?

    Answer: A PQR documents the actual parameters used and test results from a qualification test weld; it is the technical basis for writing a WPS

    A PQR records the actual welding variables used during the qualification test coupon and the results of destructive/non-destructive tests (tensile, bend, impact, hardness, RT/UT). The PQR proves the WPS is capable of producing sound welds meeting code requirements. One or more PQRs support the writing of a WPS under CSA W47.1.

  4. What effect does excessive heat input have on austenitic stainless steel HAZ?

    Answer: Promotes sensitization (carbide precipitation) reducing corrosion resistance, and causes excessive grain growth reducing toughness

    Excessive heat input holds stainless steel in the sensitization range (425–870°C) for longer, increasing carbide precipitation and chromium depletion. It also causes significant grain growth in the HAZ, which reduces toughness and ductility. Controlling heat input (using stringer beads, adequate travel speed, and interpass temperature limits) is essential.

  5. What is the recommended method for cleaning aluminum before GTAW welding?

    Answer: Degrease with acetone or approved solvent, then remove oxide layer with a stainless steel wire brush dedicated to aluminum

    Aluminum cleaning for GTAW requires two steps: first, remove oil and grease with a clean cloth and acetone or approved solvent; second, remove the aluminum oxide layer with a dedicated stainless-steel wire brush (never used on other metals to avoid contamination). The oxide melts at ~2050°C vs. ~660°C for aluminum, so it must be mechanically removed before welding.

  6. What is the weld acceptance criterion for lack of fusion in a radiographically inspected complete joint penetration weld under CSA W59?

    Answer: Lack of fusion is not acceptable — it is a rejectable defect regardless of size under CSA W59

    Under CSA W59, lack of fusion (including incomplete fusion and incomplete joint penetration in CJP welds) is a rejectable planar discontinuity regardless of size. Unlike porosity or slag inclusions which have size and frequency limits, planar defects (cracks, LOF, LOP) are inherently rejectable because they provide sharp stress concentration sites for fatigue and brittle fracture.

How this page was made: written with AI tools and published by Nathan Beja, founder of Practice Test Geeks, who is responsible for its content. Exam facts are checked against the official sources listed below. Not reviewed by a subject-matter expert. Editorial policy

Sources & references

Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy

  1. red-seal.ca — Exam format, exam information · verified Nov 2026
  2. skilledtradesontario.ca — Passing score, score release, time limit, renewal, score validity, eligibility, retake fee, test delivery, fees, retake policy · verified Nov 2026