TIG (GTAW - Gas Tungsten Arc Welding) Flashcards
6 cards from real 456A practice questions. Tap to flip, then mark Knew It or Still Learning — missed cards come back until you master them.
Read the first 6 TIG (GTAW - Gas Tungsten Arc Welding) flashcards as text
What is 'interpass cleaning' between GTAW passes and why is it important?
Answer: Removing oxides and contamination from the previous pass surface before depositing the next pass to ensure proper fusion
Even with excellent shielding, GTAW on stainless steel and aluminum can develop surface oxides on completed passes that will cause lack of fusion if the next pass is deposited over them. Brushing with a stainless-steel wire brush (dedicated to the alloy type) removes these oxides. On aluminum, brushing must be done gently to avoid embedding abrasive particles.
What is the 'autogenous' GTAW technique?
Answer: Welding without filler metal addition, relying solely on fusion of the base metal edges
Autogenous GTAW uses no filler metal — the arc simply fuses the base metal edges together. It is used for thin sheet metal, certain pipe root passes (with pre-placed insert rings), and orbital welding applications. The joint must be precisely fitted and the base metal must have sufficient cross-section to provide the required weld throat.
What is the effect of helium additions to argon shielding gas in GTAW?
Answer: Increases arc voltage and heat input, producing deeper penetration and higher travel speeds
Helium has higher thermal conductivity than argon and operates at higher arc voltages, resulting in more arc energy and deeper penetration at the same current. Ar/He mixtures (typically 25–75% He) are used for thick aluminum and copper welding where higher heat input is needed. Pure helium produces very high voltage but poor arc starts.
What does AWS D1.1 (or CSA W59 equivalent) specify as the maximum allowable face reinforcement for a complete joint penetration groove weld?
Answer: 3 mm (1/8 in) maximum reinforcement above the base metal surface
CSA W59 and AWS D1.1 limit weld face reinforcement (crown height) to a maximum of 3 mm (1/8 in) for complete joint penetration groove welds. Excessive reinforcement creates a stress concentration at the weld toes and adds unnecessary weight without improving strength. Both underreinforcement and overreinforcement are rejectable.
For GTAW orbital welding of small-bore stainless pipe in pharmaceutical/food processing systems, what additional documentation is typically required beyond a standard WPS?
Answer: Passivation procedure, surface roughness requirements (Ra), and qualification of the specific orbital machine head and parameters
In pharmaceutical and food processing (sanitary) applications, welds must meet biocompatibility requirements. Beyond standard WPS, documentation typically includes: passivation procedure (to restore the chromium oxide layer), surface roughness acceptance criteria (Ra ≤ 0.8 µm inside bore), orbital machine qualification records, and often borescope inspection photos of the weld ID.
What is the typical gas flow rate for GTAW of stainless steel using a 9.5 mm (3/8 in) gas cup?
Answer: 6–9 L/min (12–18 CFH)
For standard GTAW with a 9.5 mm diameter nozzle, approximately 6–9 L/min (12–18 CFH) of argon provides adequate shielding. Flow rate should be proportional to nozzle diameter — larger nozzles require higher flow rates to maintain coverage. Too low a flow rate results in inadequate shielding; too high causes turbulence and atmospheric air entrainment.
How this page was made: written with AI tools and published by Nathan Beja, founder of Practice Test Geeks, who is responsible for its content. Exam facts are checked against the official sources listed below. Not reviewed by a subject-matter expert. Editorial policy
Sources & references
Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy
- red-seal.ca — Exam format, exam information · verified Nov 2026
- skilledtradesontario.ca — Passing score, score release, time limit, renewal, score validity, eligibility, retake fee, test delivery, fees, retake policy · verified Nov 2026