← All 456A Flashcard Decks

MIG/FCAW (GMAW & Flux-Cored Arc Welding) Flashcards

6 cards from real 456A practice questions. Tap to flip, then mark Knew It or Still Learning — missed cards come back until you master them.

Read the first 6 MIG/FCAW (GMAW & Flux-Cored Arc Welding) flashcards as text
  1. What is the effect of increasing CO2 content in an Argon/CO2 shielding gas mixture for GMAW?

    Answer: Increases penetration and spatter; produces a more fluid weld pool and higher oxidation of weld metal

    Increasing CO2 content increases weld penetration due to the higher thermal conductivity and oxidizing nature of CO2. However, it also increases spatter, produces a more oxidizing arc, and transitions the transfer mode from spray toward globular. C25 (25% CO2) is a compromise between penetration and spatter/bead quality.

  2. What is 'porosity clustering' in FCAW welds and what does it indicate about the welding process?

    Answer: Multiple pores grouped in a local area; typically indicates intermittent shielding gas loss or surface contamination in that region

    Porosity clustering (multiple pores in a localized zone) suggests that shielding gas coverage was intermittently disrupted or that localized surface contamination (oil, moisture, mill scale) caused gas generation. It is different from uniformly scattered porosity and indicates a specific, localized problem in the process.

  3. Under Canadian workplace safety regulations (OHSR), what is required before welding begins in a confined space?

    Answer: Atmospheric testing for oxygen, combustible gases, and toxic vapours; continuous ventilation; standby person and rescue plan

    Canadian OHS regulations require a confined space entry permit with: initial and continuous atmospheric monitoring for O2 (19.5–23% range), LEL (combustible gases <10% LEL), and toxic substances; continuous forced ventilation; a trained standby person outside; written rescue procedure; and a communication system. This applies to all hot work in confined spaces.

  4. What is the purpose of a welding procedure specification (WPS) in Canadian fabrication shops operating under CSA W59?

    Answer: Documents the specific variables (process, base metal, filler, preheat, position, PWHT) that must be followed to produce an acceptable weld

    A WPS is a written document that specifies all essential, supplementary essential, and non-essential variables for a welding operation. It ensures welds are produced consistently and to the required quality. Under CSA W59 (and W47.1 for certification), WPS documents must be supported by procedure qualification records (PQR) with test results.

  5. What is 'weld distortion' and what is the most effective method to control it in GMAW fabrication?

    Answer: Warping of base metal due to thermal expansion and contraction; controlled by balanced welding sequences, clamps, backstep technique, and minimizing heat input

    Distortion results from non-uniform thermal expansion and contraction during welding. Control methods include: welding in a balanced sequence around a neutral axis, using clamps and fixtures, employing the backstep technique, minimizing passes (heat input), presetting joints to counteract anticipated distortion, and using intermittent welds where structurally permissible.

  6. What does 'pulse GMAW' (P-GMAW) offer compared to standard spray transfer?

    Answer: Achieves spray-like metal transfer at lower average current, allowing out-of-position welding with lower heat input

    Pulsed GMAW alternates between a high peak current (producing one droplet per pulse in spray mode) and a low background current (maintaining the arc). The average current is lower than spray transfer threshold, reducing heat input and pool fluidity, enabling out-of-position welding while maintaining spray-quality deposits and low spatter.

How this page was made: written with AI tools and published by Nathan Beja, founder of Practice Test Geeks, who is responsible for its content. Exam facts are checked against the official sources listed below. Not reviewed by a subject-matter expert. Editorial policy

Sources & references

Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy

  1. red-seal.ca — Exam format, exam information · verified Nov 2026
  2. skilledtradesontario.ca — Passing score, score release, time limit, renewal, score validity, eligibility, retake fee, test delivery, fees, retake policy · verified Nov 2026