← All 456A Flashcard Decks

MIG/FCAW (GMAW & Flux-Cored Arc Welding) Flashcards

6 cards from real 456A practice questions. Tap to flip, then mark Knew It or Still Learning — missed cards come back until you master them.

Read the first 6 MIG/FCAW (GMAW & Flux-Cored Arc Welding) flashcards as text
  1. What is the purpose of the contact tip in a GMAW gun?

    Answer: Transfers current to the wire and guides the wire accurately to the arc

    The contact tip (made of copper alloy) transfers welding current from the gun body to the electrode wire through electrical contact as the wire slides through it. It also guides the wire accurately toward the weld joint. Contact tips must match the wire diameter and should be replaced when worn oval or spattered shut.

  2. What is 'cold wire inclusions' or 'cold laps' in FCAW welding and how are they prevented?

    Answer: Unmelted wire tips fused onto the weld surface; prevented by proper voltage and maintaining correct torch angle

    Cold wire inclusions occur when the wire tip is not fully melted before contacting the weld pool or base metal, leaving an unmelted wire stub. Proper voltage settings ensure the wire melts completely in the arc. Torch angle must keep the arc in the leading edge of the pool.

  3. What is the recommended technique for welding a vertical-up fillet weld with GMAW short-circuit transfer?

    Answer: Triangular or Z-weave pattern with pauses at the toes to build up metal and prevent sagging

    Vertical-up GMAW (short-circuit) typically uses a triangular or Z-weave pattern. Pausing slightly at each toe ensures fusion to the base metal and builds up the weld profile. The upward travel direction allows gravity to support the solidifying weld pool and prevents undercutting.

  4. What is the difference between E70T-1 and E71T-1 FCAW electrodes?

    Answer: E70T-1 is limited to flat/horizontal positions; E71T-1 is all-position including vertical-up and overhead

    In the FCAW electrode classification, the digit after 'E7' indicates position: '0' means flat and horizontal only, '1' means all positions. E70T-1 is a flat/horizontal electrode producing a large, fluid slag; E71T-1 has a fast-freezing slag system designed for out-of-position welding.

  5. What does 'nozzle-to-work distance' (also called contact-tip-to-work distance or stick-out) affect in FCAW?

    Answer: Resistance preheating of the wire, affecting current draw, deposition rate, and penetration

    In FCAW, as in GMAW, the wire stick-out distance affects the resistive preheating of the wire between the contact tip and the arc. Longer stick-out preheats the wire more, reduces actual welding current (at the same wire feed speed), and lowers penetration. It is a critical variable specified in the WPS.

  6. Under CSA W59, what inspection requirement applies to completed FCAW welds on Category C (dynamically loaded) structures?

    Answer: Visual inspection plus non-destructive testing (NDT) as specified; radiographic or ultrasonic testing of groove welds

    CSA W59 categorizes structures by loading type. Category C (dynamically loaded) structures require enhanced inspection including NDT (RT or UT) of complete joint penetration groove welds in addition to mandatory visual inspection. The inspection level reflects the higher consequences of weld failure under cyclic loading.

How this page was made: written with AI tools and published by Nathan Beja, founder of Practice Test Geeks, who is responsible for its content. Exam facts are checked against the official sources listed below. Not reviewed by a subject-matter expert. Editorial policy

Sources & references

Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy

  1. red-seal.ca — Exam format, exam information · verified Nov 2026
  2. skilledtradesontario.ca — Passing score, score release, time limit, renewal, score validity, eligibility, retake fee, test delivery, fees, retake policy · verified Nov 2026