← All 456A Flashcard Decks

Metallurgy & Heat Treatment Flashcards

6 cards from real 456A practice questions. Tap to flip, then mark Knew It or Still Learning — missed cards come back until you master them.

Read the first 6 Metallurgy & Heat Treatment flashcards as text
  1. What is 'stress relieving' and at what typical temperature is it performed on carbon steel weldments?

    Answer: Heating to 595–650°C, holding for 1 hour per 25 mm of thickness, then slow cooling; reduces residual stresses without significant microstructural change

    Stress relieving (PWHT for carbon steel) is performed at 595–650°C (below Ac1) for a soak time of minimum 1 hour per 25 mm of nominal thickness. The elevated temperature allows plastic flow at the microscopic level, reducing peak residual stresses by approximately 85–90%. Controlled heating and cooling rates prevent thermal shock in thick sections.

  2. What is 'blue brittleness' in carbon steel and how does it relate to welding?

    Answer: Reduced ductility when steel is strained in the temperature range 200–370°C due to strain aging from nitrogen and carbon; avoid welding or mechanically working steel in this temperature range

    Blue brittleness (also called dynamic strain aging) occurs when carbon steel is strained between approximately 200–370°C, where interstitial nitrogen and carbon atoms migrate to and lock dislocations, reducing ductility. The name comes from the blue oxidation colour of steel at these temperatures. While rare in standard welding, it can affect susceptibility to cracking in certain heat-straightening or in-service conditions.

  3. What is the 'nil ductility transition temperature' (NDTT) as measured by a drop-weight test?

    Answer: The highest temperature at which a standard drop-weight specimen fractures completely (nil ductility); above the NDTT, the steel has adequate toughness for service

    The nil-ductility transition temperature (NDTT) is determined by the Pellini drop-weight test (ASTM E208). It is the highest temperature at which the specimen shows no plastic deformation (nil ductility) — below NDTT, the steel is in the brittle fracture regime. Structural design requires the service temperature to be above NDTT plus a margin. It is used for designing pressure vessels and bridges in cold Canadian climates.

  4. What is the difference between 'incomplete fusion' and 'incomplete joint penetration' as weld discontinuities?

    Answer: Incomplete fusion is lack of bonding between weld metal and base metal at the fusion face; incomplete joint penetration is failure to fill the root of the groove to the required depth

    Incomplete fusion (LOF) is a lack of metallurgical bonding between weld metal and the adjacent base metal or weld pass at the fusion face — the metals are in contact but not bonded. Incomplete joint penetration (LOP) is the failure of the weld to penetrate to the required depth at the root of a groove weld. Both are planar discontinuities and rejectable in most codes.

  5. What is 'sigma phase embrittlement' and in which temperatures and materials does it occur?

    Answer: A hard, brittle FeCr intermetallic phase that forms in austenitic and duplex stainless steels held between 600–900°C; dramatically reduces toughness and corrosion resistance

    Sigma phase (FeCr intermetallic compound) precipitates in austenitic and duplex stainless steels exposed to temperatures between approximately 600–900°C (especially near 750°C). It causes severe embrittlement, reducing impact toughness to near zero and depleting chromium and molybdenum from the matrix, reducing corrosion resistance. Sigma phase can form during slow cooling in welding, prolonged PWHT, or high-temperature service.

  6. What does a 'weld metal tensile test' (all-weld-metal tensile) measure and what results are required for E7018 weld metal qualification?

    Answer: Tensile and yield strength of the deposited weld metal; E7018 requires minimum 480 MPa (70 ksi) UTS and minimum 400 MPa (58 ksi) yield strength with 22% elongation

    The all-weld-metal tensile test uses a specimen machined entirely from deposited weld metal (no base metal included) to measure the intrinsic mechanical properties of the filler metal deposit. For E7018 per CSA W48, the weld metal must meet: minimum UTS 480 MPa, minimum yield strength 400 MPa, minimum elongation 22%, and minimum reduction of area 50%. These values match the '70' designation.

How this page was made: written with AI tools and published by Nathan Beja, founder of Practice Test Geeks, who is responsible for its content. Exam facts are checked against the official sources listed below. Not reviewed by a subject-matter expert. Editorial policy

Sources & references

Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy

  1. red-seal.ca — Exam format, exam information · verified Nov 2026
  2. skilledtradesontario.ca — Passing score, score release, time limit, renewal, score validity, eligibility, retake fee, test delivery, fees, retake policy · verified Nov 2026