Metallurgy & Heat Treatment Flashcards
6 cards from real 456A practice questions. Tap to flip, then mark Knew It or Still Learning — missed cards come back until you master them.
Read the first 6 Metallurgy & Heat Treatment flashcards as text
What is the difference between 'normalizing' and 'annealing' heat treatments for carbon steel?
Answer: Normalizing uses air cooling to produce a fine pearlite microstructure; annealing uses furnace (slow) cooling to produce a softer, coarser structure
Both normalizing and annealing heat carbon steel above Ac3 (austenite region) to refine grain structure and relieve stresses. Normalizing uses air cooling, producing a fine pearlite microstructure with moderate strength. Annealing uses very slow furnace cooling, producing a coarser, softer microstructure with maximum ductility. Normalizing is used to refine grain and improve toughness; annealing is used to maximize machinability or ductility.
What does 'austenite' mean in the context of carbon steel metallurgy?
Answer: The face-centred cubic (FCC) iron phase stable at high temperatures (above approximately 727°C for pure iron) that can dissolve large amounts of carbon
Austenite is the high-temperature FCC phase of iron (gamma iron) that is stable above approximately 727°C (the A1 temperature). Its FCC crystal structure can accommodate up to 2.14% carbon in solid solution. During welding, the base metal adjacent to the fusion line is heated into the austenite region; the resulting microstructure after cooling depends on the cooling rate and composition.
What is the Charpy impact test used to measure in welded joints?
Answer: Notch toughness (energy absorbed during fracture) at specified temperatures, indicating resistance to brittle fracture
The Charpy V-notch impact test measures the energy (in joules) absorbed when a notched specimen is fractured by a swinging pendulum hammer. For weld qualification, specimens are taken from the weld metal and HAZ and tested at the specified minimum design temperature. The test quantifies toughness — resistance to brittle fracture — which is critical for structural applications in cold climates.
What is the Vickers Hardness (HV) limit typically specified for the HAZ in sour service (H2S) environments per NACE MR0175/ISO 15156?
Answer: 250 HV maximum
NACE MR0175/ISO 15156 (materials for sour service) specifies a maximum HAZ hardness of 250 HV (approximately 22 HRC) for carbon and low-alloy steels to prevent sulfide stress cracking (SSC). Harder zones are more susceptible to hydrogen embrittlement from H2S environments. This limit drives preheat, heat input, and PWHT requirements for sour service welding.
What is 'stress corrosion cracking' (SCC) and which material-environment combination is most relevant for Canadian pressure piping welding?
Answer: Cracking from the combined effect of tensile stress and a corrosive environment; austenitic stainless steel in chloride-containing environments is the most common concern
SCC requires three simultaneous conditions: susceptible material, tensile stress (residual or applied), and specific corrosive environment. Austenitic stainless steel in chloride environments (including some process streams and marine atmospheres) is the classic SCC combination. Residual welding stresses are a major contributor; PWHT or post-weld stress relief can reduce susceptibility.
What is 'carbon migration' (carbon diffusion) in dissimilar metal welds between carbon steel and stainless steel?
Answer: Carbon migrates from the carbon steel into the stainless steel weld metal at elevated service temperatures, creating a decarburized zone in the carbon steel and a carburized zone in the stainless
In dissimilar metal welds between carbon steel and austenitic stainless steel operating at elevated temperatures (above ~400°C), carbon migrates from the lower chromium (carbon steel) side toward the higher chromium (stainless) side, where it is more thermodynamically stable. This creates a soft, weak decarburized zone in the carbon steel HAZ and a hard, brittle carburized zone in the stainless weld metal, reducing creep and fatigue resistance.
How this page was made: written with AI tools and published by Nathan Beja, founder of Practice Test Geeks, who is responsible for its content. Exam facts are checked against the official sources listed below. Not reviewed by a subject-matter expert. Editorial policy
Sources & references
Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy
- red-seal.ca — Exam format, exam information · verified Nov 2026
- skilledtradesontario.ca — Passing score, score release, time limit, renewal, score validity, eligibility, retake fee, test delivery, fees, retake policy · verified Nov 2026