GTAW TIG Flashcards
6 cards from real 456A practice questions. Tap to flip, then mark Knew It or Still Learning — missed cards come back until you master them.
Read the first 6 GTAW TIG flashcards as text
What type of electrode is used in GTAW (TIG) welding and why is it called 'non-consumable'?
Answer: A tungsten electrode that creates the arc but does not melt into the weld pool; it is 'non-consumable' because it has a much higher melting point than the base metal
GTAW uses a tungsten electrode with a melting point of approximately 3,422°C, far higher than the melting point of steel (~1,500°C) or aluminium (~660°C). The tungsten creates and sustains the arc but does not melt into the weld pool. Filler metal, when needed, is added separately by hand-feeding a filler rod.
What shielding gas is most commonly used in GTAW welding?
Answer: Pure argon (100%) or argon-helium mixtures
Pure argon is the most common shielding gas for GTAW because it provides excellent arc stability, good shielding effectiveness, and is suitable for most metals. Argon-helium mixtures are used when more heat input is needed (such as for thick aluminium), as helium increases arc energy. CO₂ and oxygen are never used in GTAW as they would destroy the tungsten electrode.
What polarity is used for GTAW welding of carbon steel and stainless steel?
Answer: DCEN (DC Electrode Negative / Straight Polarity) for maximum penetration and minimal electrode heating
DCEN (straight polarity) is used for GTAW welding of steel, stainless steel, copper, and most metals. With DCEN, about two-thirds of the arc heat is directed at the workpiece (deeper penetration) and only one-third at the tungsten electrode (extending electrode life). AC is used for aluminium and magnesium to provide cathodic cleaning.
Why is AC polarity used for GTAW welding of aluminium?
Answer: The electrode-positive (EP) half-cycle provides a cathodic cleaning action that breaks up the aluminium oxide layer, while the electrode-negative (EN) half-cycle provides penetration
AC alternates between DCEP and DCEN. The DCEP portion provides cathodic cleaning action that breaks up the tenacious aluminium oxide layer (which melts at 2,072°C — far higher than aluminium at 660°C). The DCEN portion provides penetration and reduces electrode heating. Modern inverters allow balance control between EP and EN portions.
What is the purpose of post-flow gas in GTAW welding?
Answer: To continue shielding the cooling tungsten electrode and weld pool after the arc is extinguished, preventing oxidation
Post-flow continues the shielding gas flow after the arc is terminated, protecting both the hot tungsten electrode and the solidifying weld pool from atmospheric contamination. Without adequate post-flow (typically 1 second per 10 amps), the tungsten tip oxidizes and the weld crater can develop porosity or discolouration.
What is the correct method for preparing (grinding) a tungsten electrode for DC welding?
Answer: Grind it to a tapered point along the length axis (longitudinal grinding) with the grinding marks running lengthwise, not across the tip
For DC welding, the tungsten should be ground to a tapered point using a dedicated grinding wheel. Grinding marks must run lengthwise (longitudinally) along the taper, not circumferentially, as circumferential marks cause arc wander. The taper length is typically 2 to 2.5 times the electrode diameter. A flat or truncated tip may be used for high-amperage applications.
How this page was made: written with AI tools and published by Nathan Beja, founder of Practice Test Geeks, who is responsible for its content. Exam facts are checked against the official sources listed below. Not reviewed by a subject-matter expert. Editorial policy
Sources & references
Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy
- red-seal.ca — Exam format, exam information · verified Nov 2026
- skilledtradesontario.ca — Passing score, score release, time limit, renewal, score validity, eligibility, retake fee, test delivery, fees, retake policy · verified Nov 2026