GTAW TIG Flashcards
6 cards from real 456A practice questions. Tap to flip, then mark Knew It or Still Learning — missed cards come back until you master them.
Read the first 6 GTAW TIG flashcards as text
What is a gas lens in a GTAW torch and what advantage does it provide?
Answer: A fine mesh screen that produces a smooth, laminar gas flow for better shielding coverage, especially at extended stick-out distances and on joints with restricted access
A gas lens replaces the standard collet body and uses multiple layers of fine stainless steel mesh to convert turbulent gas flow into smooth, laminar flow. This provides more effective shielding coverage, allows longer tungsten stick-out for better visibility and access to tight joints, and reduces gas consumption while improving weld quality.
What causes tungsten contamination in a GTAW weld?
Answer: Dipping the tungsten electrode into the weld pool, which deposits tungsten particles in the weld
Tungsten contamination occurs when the electrode tip contacts the molten weld pool, depositing tungsten particles in the weld. Tungsten inclusions appear as bright white spots on radiographs and are considered weld defects in critical applications. If contamination occurs, the affected area must be ground out, and the tungsten must be re-prepared.
What is the function of a foot pedal (foot amptrol) in GTAW welding?
Answer: To provide real-time variable amperage control during welding, allowing the welder to increase or decrease heat input while welding
The foot pedal (amptrol) gives the GTAW welder precise, real-time control over welding current from zero to maximum while welding. This allows the welder to increase heat for thicker sections, reduce heat approaching edges to prevent burn-through, and taper the current down at the end to properly fill the crater.
What is the purpose of adding filler metal in GTAW welding?
Answer: To add material to the weld joint for building up the weld cross-section, filling gaps, and matching the base metal composition and strength
Filler metal is added separately (by hand-feeding a rod) to provide additional weld metal for filling joints, building up weld reinforcement, bridging gaps, and matching the base metal's composition and mechanical properties. Some GTAW welds on thin material can be made autogenously (without filler) by fusing the base metal edges together.
What is a GTAW walking the cup technique used for?
Answer: Rocking the ceramic gas cup alternately on each side of the joint to maintain consistent travel speed, torch angle, and arc length while welding pipe or tubing
Walking the cup is a GTAW pipe welding technique where the welder rocks the ceramic gas cup from side to side on the pipe bevel, alternating contact points like walking. This provides consistent torch angle, travel speed, and arc length, producing uniform weave beads — particularly valuable in pipe root and fill passes where consistency is critical.
What is the recommended cup (nozzle) size selection for GTAW welding?
Answer: Select a cup diameter that provides adequate shielding coverage — generally the cup size number equals the inside diameter in sixteenths of an inch (e.g., #8 cup = 1/2 inch / 12.7 mm)
Cup size selection depends on the joint configuration, tungsten size, and gas flow rate. The cup must be large enough to provide adequate shielding coverage without excessive gas consumption. Cup size numbers indicate the inside diameter in sixteenths of an inch (e.g., #8 = 8/16 = 1/2 inch). Larger cups are used for wider welds and higher amperages.
How this page was made: written with AI tools and published by Nathan Beja, founder of Practice Test Geeks, who is responsible for its content. Exam facts are checked against the official sources listed below. Not reviewed by a subject-matter expert. Editorial policy
Sources & references
Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy
- red-seal.ca — Exam format, exam information · verified Nov 2026
- skilledtradesontario.ca — Passing score, score release, time limit, renewal, score validity, eligibility, retake fee, test delivery, fees, retake policy · verified Nov 2026