GMAW MIG Flashcards
6 cards from real 456A practice questions. Tap to flip, then mark Knew It or Still Learning — missed cards come back until you master them.
Read the first 6 GMAW MIG flashcards as text
What is the difference between push (forehand) and pull (backhand) gun angle in GMAW?
Answer: Push angle tilts the gun in the direction of travel for less penetration and wider bead; pull angle tilts away from travel direction for deeper penetration and narrower bead
Push (forehand) technique tilts the gun 10-15° in the direction of travel, placing the arc ahead of the puddle. This produces less penetration, a wider/flatter bead, and better visibility. Pull (backhand) tilts the gun 10-15° away from the direction of travel, producing deeper penetration, a narrower/more convex bead, and more spatter.
What is the purpose of anti-spatter compound in GMAW welding?
Answer: To coat the nozzle, workpiece surface, and fixtures to prevent spatter from adhering, making cleanup easier
Anti-spatter compound is applied to the inside of the gas nozzle, the workpiece surface near the weld, and fixtures/clamps. It prevents molten spatter from welding onto these surfaces, reducing cleanup time and preventing nozzle blockage. It must not be applied to the weld joint itself as it can contaminate the weld.
What causes excessive spatter in GMAW welding?
Answer: Voltage set too high or too low for the wire feed speed, contaminated base metal, wrong shielding gas, excessive stick-out, or moisture on the wire
Excessive spatter results from: voltage too low (unstable short-circuit transfer), voltage too high (long arc, excessive droplet spray), contaminated or rusty base metal, wrong or depleted shielding gas, excessive stick-out, moisture on the wire or base metal, or worn/wrong-sized contact tip. Proper parameter balance minimizes spatter.
What is pulsed GMAW and what are its advantages?
Answer: An electronically controlled process that alternates between high peak current (for droplet transfer) and low background current (to maintain the arc), allowing spray-type transfer at lower average heat input
Pulsed GMAW uses a power source that rapidly switches between high peak current (which detaches a single droplet per pulse in a spray-like manner) and low background current (which maintains the arc without metal transfer). This provides the quality of spray transfer with lower average heat input, enabling use on thinner materials and in all positions.
What is the correct procedure for setting up a GMAW machine for a new welding job?
Answer: Select correct wire size and type, install matching drive rolls and contact tip, set gas type and flow rate, adjust wire feed speed and voltage per the manufacturer's chart, and make test welds
Proper GMAW setup includes: (1) selecting the correct wire type and diameter for the application, (2) installing matching drive rolls, liner, and contact tip, (3) selecting the correct shielding gas and setting the flow rate (typically 15-20 L/min), (4) setting wire feed speed and voltage using the manufacturer's parameter chart, (5) adjusting stick-out, and (6) making test welds to fine-tune.
In GMAW, what does a constant voltage (CV) power source do differently from a constant current (CC) source?
Answer: CV maintains a set voltage and allows amperage to vary with arc length changes (self-regulating); CC maintains set amperage and allows voltage to vary — GMAW uses CV
A CV power source maintains a relatively constant output voltage while allowing the amperage to fluctuate in response to changes in arc length. This creates a self-regulating arc: if stick-out decreases (shorter arc), current increases, melting wire faster to restore the arc length. This self-regulation is essential for the continuous wire-feed GMAW process.
How this page was made: written with AI tools and published by Nathan Beja, founder of Practice Test Geeks, who is responsible for its content. Exam facts are checked against the official sources listed below. Not reviewed by a subject-matter expert. Editorial policy
Sources & references
Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy
- red-seal.ca — Exam format, exam information · verified Nov 2026
- skilledtradesontario.ca — Passing score, score release, time limit, renewal, score validity, eligibility, retake fee, test delivery, fees, retake policy · verified Nov 2026