FCAW Flashcards
6 cards from real 456A practice questions. Tap to flip, then mark Knew It or Still Learning — missed cards come back until you master them.
Read the first 6 FCAW flashcards as text
What are the two types of FCAW (Flux-Cored Arc Welding)?
Answer: Gas-shielded FCAW (FCAW-G) using external shielding gas and self-shielded FCAW (FCAW-S) where the flux core provides all shielding
FCAW has two variants: gas-shielded (FCAW-G or dual-shield) uses flux-cored wire plus external shielding gas (typically CO₂ or argon-CO₂ mix) for dual protection. Self-shielded (FCAW-S or inner-shield) relies entirely on the flux core to produce shielding gas and slag — no external gas is needed, making it ideal for outdoor and windy conditions.
What is the main advantage of self-shielded FCAW over GMAW for outdoor structural welding in Canada?
Answer: The self-generated shielding is not affected by wind, making it reliable for outdoor and field welding in Canadian weather conditions
Self-shielded FCAW generates its own protective atmosphere from the decomposing flux core, so wind cannot blow away the shielding as it can with GMAW's external gas. This makes FCAW-S the preferred process for outdoor structural steel erection, bridge work, and field welding across Canada's varied weather conditions.
What type of polarity is typically used for self-shielded FCAW?
Answer: DCEN (DC Electrode Negative / Straight Polarity) for most self-shielded wires
Most self-shielded FCAW wires are designed for DCEN (straight polarity), which concentrates heat in the workpiece and produces shallower penetration suited to the process. Gas-shielded FCAW wires typically use DCEP. Always verify the wire manufacturer's specifications, as using the wrong polarity can cause severe porosity and poor weld quality.
What is the purpose of the flux core inside an FCAW wire?
Answer: To produce shielding gas, form protective slag, add deoxidizers and alloying elements, and stabilize the arc — similar functions to SMAW flux coating
The flux core serves multiple functions similar to a SMAW electrode coating: it produces shielding gases (for self-shielded wires), creates a slag blanket that protects the cooling weld, adds deoxidizers to clean the weld metal, contributes alloying elements, and stabilizes the arc. Different flux formulations are designed for specific applications.
What is the typical wire stick-out (contact-tip-to-work distance) for FCAW?
Answer: 19 to 38 mm (3/4 to 1-1/2 in.) — longer than GMAW
FCAW typically uses a longer stick-out (19 to 38 mm / 3/4 to 1-1/2 inches) compared to GMAW. Self-shielded FCAW often uses even longer stick-out (up to 50 mm). The longer stick-out preheats the wire through resistance heating and is part of the designed operating characteristics of flux-cored wires.
What is worm tracking (gas marks) on an FCAW weld surface?
Answer: Small surface marks or trails on the weld bead caused by gas escaping through the slag as it solidifies; usually cosmetic but can indicate improper technique or excessive voltage
Worm tracking appears as small herringbone or track-like marks on the surface of FCAW welds. They are caused by gas escaping through the solidifying slag. While primarily cosmetic (not typically a structural concern), excessive worm tracking may indicate voltage is too high, excessive stick-out, or contaminated base metal.
How this page was made: written with AI tools and published by Nathan Beja, founder of Practice Test Geeks, who is responsible for its content. Exam facts are checked against the official sources listed below. Not reviewed by a subject-matter expert. Editorial policy
Sources & references
Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy
- red-seal.ca — Exam format, exam information · verified Nov 2026
- skilledtradesontario.ca — Passing score, score release, time limit, renewal, score validity, eligibility, retake fee, test delivery, fees, retake policy · verified Nov 2026