← All 456A Flashcard Decks

Blueprint Reading, Weld Symbols & Joint Preparation Flashcards

6 cards from real 456A practice questions. Tap to flip, then mark Knew It or Still Learning — missed cards come back until you master them.

Read the first 6 Blueprint Reading, Weld Symbols & Joint Preparation flashcards as text
  1. What is the difference between 'effective throat' and 'actual throat' of a fillet weld?

    Answer: Actual throat is the distance from the root to the face including convexity; effective throat is the shortest distance from the root to the weld face (hypotenuse), which is used for strength calculations

    For an equal-leg fillet weld with leg size 'w', the effective (theoretical) throat = w × 0.707. It is the shortest distance from the root to the theoretical face of the weld and is used for stress calculations. The actual throat includes any weld convexity above the theoretical face. Codes use the effective throat for design purposes as convexity is not considered reliably load-bearing.

  2. On a structural drawing, a fillet weld symbol shows '8' to the left and '150-300' to the right of the fillet symbol. What does this specify?

    Answer: 8 mm leg fillet welds, 150 mm long, spaced 300 mm apart (intermittent welds)

    In standard weld symbol notation: the number to the left of the symbol is the weld size (8 mm leg), and the number(s) to the right indicate weld length and pitch. '150-300' means weld segments 150 mm long at 300 mm pitch (centre-to-centre spacing). This is an intermittent fillet weld specification — commonly used for non-critical connections to reduce heat input and cost.

  3. What does a double-sided V-groove symbol (X-groove) indicate on a drawing?

    Answer: Full penetration groove weld to be made from both sides of the joint

    The double-V groove (X-groove) symbol shows V-groove symbols on both sides of the reference line, indicating that the joint is to be prepared (bevelled) and welded from both sides. This is used for thick plate where welding from one side would require an excessively wide groove, resulting in excessive weld metal and distortion. It provides full penetration with less total weld metal than a single V.

  4. What is a 'backing symbol' (rectangle) on a groove weld symbol and what does it specify?

    Answer: A backing bar or backing material is to be used at the root of the joint to support the root pass and ensure full penetration

    The backing symbol (a rectangle below the reference line, on the other side from the weld symbol) indicates a backing bar or ring is required. In most structural applications, a CSA/ASTM steel backing bar is permanently fused into the joint. On process piping and pressure vessels, a removable ceramic or copper backing may be used. The presence or absence of backing affects the required root opening and edge preparation.

  5. What does the 'contour symbol' on a weld symbol specify?

    Answer: The required finished profile of the weld face — flat, convex, or concave — and whether finishing is required

    Contour symbols are placed above or below the weld symbol to specify the desired weld face profile: a straight line (flush/flat), a convex arc, or a concave arc. A letter below the contour symbol specifies the finishing method: G (grinding), M (machining), C (chipping), R (rolling), or U (unspecified). These specifications are important for fatigue-critical joints where notches at the weld toe must be minimized.

  6. On a drawing, a fillet weld symbol has a '(E)' notation. What does this indicate?

    Answer: The effective throat dimension is specified (rather than the leg size)

    When the letter 'E' appears before or with a fillet weld size, it indicates that the dimension given is the effective throat rather than the leg length. This is sometimes used when a specific throat dimension is required for stress calculations and the engineer specifies it directly rather than converting to a leg size. The fabricator must determine the required leg size from the effective throat (leg = throat ÷ 0.707).

How this page was made: written with AI tools and published by Nathan Beja, founder of Practice Test Geeks, who is responsible for its content. Exam facts are checked against the official sources listed below. Not reviewed by a subject-matter expert. Editorial policy

Sources & references

Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy

  1. red-seal.ca — Exam format, exam information · verified Nov 2026
  2. skilledtradesontario.ca — Passing score, score release, time limit, renewal, score validity, eligibility, retake fee, test delivery, fees, retake policy · verified Nov 2026