Mechanical Maintenance Flashcards
36 cards from real Ramsay Test practice questions. Tap to flip, then mark Knew It or Still Learning — missed cards come back until you master them.
Read the first 20 Mechanical Maintenance flashcards as text
What type of maintenance is performed on a scheduled basis regardless of equipment condition?
Answer: Preventive maintenance
Preventive maintenance (PM) is scheduled at regular intervals (time-based or usage-based) regardless of equipment condition. It aims to prevent failures before they occur.
What does vibration analysis in predictive maintenance primarily detect?
Answer: Imbalance, misalignment, bearing wear, and looseness in rotating machinery
Vibration analysis measures and interprets vibration signatures to identify mechanical problems in rotating equipment. Different defects (imbalance, misalignment, bearing faults) produce characteristic frequency patterns.
A shaft coupling is misaligned. Which type of coupling can best accommodate angular misalignment?
Answer: Flexible jaw coupling
Flexible jaw (spider) couplings can accommodate small amounts of angular, parallel, and axial misalignment through the elastomeric spider element. Rigid couplings cannot tolerate any misalignment.
What is the correct method for installing a bearing onto a shaft using the inner ring press-fit method?
Answer: Apply force only to the inner ring using a bearing installation tool or press
When press-fitting a bearing onto a shaft, force must be applied only to the inner ring (the interference fit surface). Striking the outer ring transmits force through the rolling elements, causing damage.
Which lubrication method is best suited for high-speed, lightly loaded bearings?
Answer: Oil mist or oil bath lubrication
High-speed bearings generate significant heat. Oil mist or oil bath provides continuous, light lubrication with good cooling. Heavy grease packing at high speeds increases friction and heat.
What is the primary function of a V-belt drive in mechanical power transmission?
Answer: To transmit power between shafts while allowing for speed ratio changes and absorbing shock
V-belt drives transmit power through friction between the belt and sheave grooves. They allow different speed ratios (by changing sheave sizes), absorb shock loads, and can handle misalignment better than chains.
When replacing a hydraulic seal, why is it critical to install the seal in the correct orientation?
Answer: Seals have a directional lip that must face the pressure side to function properly
Dynamic seals (lip seals, O-rings in some configurations) have directional lips designed to be energized by system pressure. Reversed installation prevents the lip from sealing against the mating surface, causing immediate leakage.
What does 'backlash' refer to in a gear set?
Answer: The small clearance between mating gear teeth allowing for lubrication and thermal expansion
Backlash is the intentional clearance between mating gear teeth. It accommodates lubrication film thickness, thermal expansion, and manufacturing tolerances. Too little causes binding; too much increases noise and wear.
A pump is cavitating. Which of the following conditions is the most likely cause?
Answer: Insufficient inlet pressure or excessive suction lift causing vapor bubble formation
Cavitation occurs when local pressure in the pump drops below the fluid's vapor pressure, forming vapor bubbles that collapse violently. Causes include high suction lift, restricted inlet, or fluid temperature too high.
What is the purpose of a torque wrench in mechanical maintenance?
Answer: To apply a precise, measured amount of torque to fasteners
A torque wrench ensures fasteners are tightened to the manufacturer's specified torque value. Under-torquing causes looseness; over-torquing can strip threads, stretch bolts, or crush gaskets.
When performing shaft alignment using a dial indicator, a 'soft foot' condition refers to:
Answer: One or more machine feet not making full contact with the base, causing distortion when bolted down
Soft foot occurs when one or more machine mounting feet don't sit flat on the base. When bolted down, it distorts the machine frame, causing misalignment, vibration, and bearing wear. Must be corrected before alignment.
What type of bearing is best suited for heavy radial loads at low to moderate speeds?
Answer: Cylindrical roller bearing
Cylindrical roller bearings have higher radial load capacity than ball bearings of similar size because contact is along a line rather than at a point. They're ideal for heavy radial loads but can't handle thrust loads.
In a gear drive, a speed reducer with a 5:1 ratio is connected to a 1,800 RPM motor. What is the output shaft speed?
Answer: 360 RPM
Output speed = Input speed / Gear ratio = 1,800 / 5 = 360 RPM. A speed reducer reduces shaft speed and proportionally increases torque (at constant power).
What is the purpose of a thermal imaging survey in predictive maintenance?
Answer: To identify hot spots in electrical connections, bearings, or other components indicating abnormal heat
Thermal (infrared) imaging detects abnormal heat patterns caused by loose electrical connections, overloaded circuits, failing bearings, blocked cooling passages, or insulation breakdown before failures occur.
Which of the following correctly describes the process of lapping two mating surfaces?
Answer: Using an abrasive compound between surfaces to achieve extremely precise, flat mating contact
Lapping uses fine abrasive compound applied between two mating surfaces which are then rubbed together. This removes high spots and creates precise, leak-free flat-on-flat contact, common on valve seats and precision flanges.
A rotating machine is experiencing high axial (thrust) loads. Which bearing type is specifically designed to handle this?
Answer: Tapered roller thrust bearing or angular contact ball bearing
Tapered roller bearings and angular contact ball bearings are designed to handle combinations of radial and axial loads. Pure thrust bearings handle axial loads only. Cylindrical roller bearings handle radial loads only.
What does the oil viscosity rating ISO VG 46 indicate?
Answer: The oil has a kinematic viscosity of approximately 46 centistokes at 40°C
ISO VG (Viscosity Grade) numbers indicate kinematic viscosity in centistokes (cSt) at 40°C. VG 46 means approximately 46 cSt. Higher numbers = thicker oil, suited for higher loads or temperatures.
When replacing a flat gasket on a flanged pipe joint, what is the correct torquing sequence for the bolts?
Answer: Tighten bolts in a cross pattern (star sequence) to even compression
The cross (star) pattern applies even compression across the gasket, preventing distortion and uneven seating. Bolts are typically torqued in 3 passes: 30%, 70%, then 100% of final torque.
What is the primary advantage of predictive maintenance over preventive maintenance?
Answer: Maintenance is performed only when actual equipment condition indicates it is needed, reducing unnecessary work
Predictive maintenance uses condition monitoring (vibration, thermography, oil analysis) to schedule maintenance based on actual equipment wear. This avoids both early replacement of good components and unexpected failures.
A chain drive is making noise and the chain appears to sag excessively. What maintenance action is required?
Answer: Adjust chain tension to specifications and lubricate the chain
Chain sag indicates wear elongation or improper tension. Adjust the center distance between sprockets to restore proper sag (typically 2-4% of span length). Lubricate to reduce further wear. If elongated beyond 3%, replace the chain.
Written and edited by Nathan Beja, founder of Practice Test Geeks, with AI assistance. Exam facts are checked against the official sources linked below. Editorial policy
Sources & references
Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy
- ramsaycorp.com — Test delivery, fees, exam format, time limit, score validity · verified Oct 2026