Ramsay Test Mechanical Reasoning 5

Question 1

A compound gear train consists of three meshed gears: Gear A (20 teeth) drives Gear B (60 teeth), which shares a shaft with Gear C (15 teeth), which drives Gear D (45 teeth). If Gear A rotates at 1,800 RPM, what is the output speed of Gear D?

Accepted Answer

200 RPM

Answer

In a compound gear train, each stage multiplies the ratio. Stage 1: A→B ratio = 20/60 = 1/3, so B rotates at 1800 × (1/3) = 600 RPM. Since B and C share a shaft, C also rotates at 600 RPM. Stage 2: C→D ratio = 15/45 = 1/3, so D rotates at 600 × (1/3) = 200 RPM. Overall ratio = 1/9.

Question 2

Two pistons are connected in a hydraulic system. Piston A has a diameter of 2 inches and Piston B has a diameter of 6 inches. A force of 50 lbs is applied to Piston A. What is the mechanical advantage, and how much weight can Piston B lift?

Accepted Answer

MA = 9; lifts 450 lbs

Answer

Hydraulic mechanical advantage is based on the ratio of areas, not diameters. Area = π(d/2)². Piston A area = π(1)² = π in². Piston B area = π(3)² = 9π in². MA = 9π/π = 9. Output force = 50 × 9 = 450 lbs. The common mistake is using the diameter ratio (3) instead of the area ratio (9).

Question 3

A steel beam is supported at both ends with a concentrated load placed 1/3 of the way from the left support. Compared to the same load placed at the center, how do the two support reactions change?

Accepted Answer

The right support carries more load when the weight is at 1/3 from left; both supports carry equal load at center

Answer

By the principle of moments, a support reaction is proportional to the load's proximity to the opposite support. When the load is 1/3 from the left (2/3 from the right), the right support carries 2/3 of the load and the left carries 1/3 — the right carries MORE. When centered, each support carries half. This is counterintuitive: the farther support from the load actually carries less weight.

Question 4

A spring with a stiffness of 400 N/m is compressed 0.05 m and placed under a 2 kg block on a frictionless surface. When released, the block launches horizontally. Ignoring air resistance, approximately how fast is the block moving the instant it leaves the spring?

Accepted Answer

1.0 m/s

Answer

Using conservation of energy: elastic PE = kinetic energy. (1/2)kx² = (1/2)mv². So v = x√(k/m) = 0.05 × √(400/2) = 0.05 × √200 = 0.05 × 14.14 ≈ 0.707 m/s. Wait — recalculating: v² = kx²/m = (400 × 0.0025)/2 = 1/2 = 0.5; v = √0.5 ≈ 0.707 m/s. The closest answer is 1.0 m/s — actually the exact answer is ≈0.707 m/s, which rounds to 0.7 m/s.

Question 5

A mechanic uses a torque wrench to tighten a bolt. The handle is 0.4 m long and is gripped at its very end. To produce 80 N·m of torque, how much force is needed? Now, if the mechanic's hand slips and grips the wrench only 0.1 m from the pivot, how much additional force is needed to achieve the same torque?

Accepted Answer

200 N initial; 600 N additional

Answer

Torque = Force × distance. At 0.4 m: F = 80/0.4 = 200 N. At 0.1 m: F = 80/0.1 = 800 N. Additional force needed = 800 − 200 = 600 N. This illustrates why grip position dramatically affects required effort — moving 4× closer to the pivot requires 4× the force.

Ramsay Test Practice Test

Ramsay Test Practice Test

Ramsay Test Mechanical Reasoning 5