Ramsay Test Logical Thinking & Problem Solving 6

Question 1

A maintenance technician notices that a conveyor motor trips its thermal overload every day at approximately 2:15 PM, but runs fine all morning. The ambient temperature in the facility is controlled. Which of the following is the MOST logical root cause to investigate first?

Accepted Answer

A production load increase that occurs mid-shift as a second line comes online

Answer

The consistent 2:15 PM timing points to a repeatable operational change rather than a component failure or external utility issue. A second production line coming online mid-shift would create a predictable, recurring load increase on the conveyor at the same time each day. A drifting relay (B) would show irregular timing. Utility voltage drops (C) would typically affect all equipment simultaneously and would appear in logs. Bearing lubrication breakdown (D) would worsen over weeks, not reset each morning.

Question 2

In a logical number series: 3, 6, 11, 18, 27, 38, ___ — what is the next number?

Accepted Answer

51

Answer

The differences between consecutive terms are: 3, 5, 7, 9, 11, 13 — a sequence of odd numbers increasing by 2. Adding 13 to 38 gives 51. This is a second-order arithmetic sequence where the rate of change itself changes by a constant value (+2 each step), a pattern that requires identifying the differences of differences rather than a simple multiplier.

Question 3

A technician is troubleshooting an intermittent fault in a pneumatic press. The press fails to build full pressure, but only on every third or fourth cycle, and returns to normal on its own. The compressor output and main supply line pressure both test normal. Which troubleshooting approach is MOST logically sound?

Accepted Answer

Observe whether the fault correlates with a specific phase of the cycle and instrument the system to capture the event in real time

Answer

Intermittent faults require data capture during the failure event, not assumption-based replacement or compensation. Option B is correct because it uses systematic observation to isolate where in the cycle the fault occurs before committing to a repair — a core principle of logical troubleshooting. Option A (replace seals) is guessing without evidence. Option C (raise pressure) treats the symptom and could cause damage. Option D assumes a cause without evidence and cleaning may not survive the next cycle.

Question 4

Four technicians — Ava, Ben, Cal, and Dee — each specialize in exactly one of four systems: electrical, hydraulic, pneumatic, and mechanical. Using these clues: (1) Ava does not work on fluid-based systems. (2) Ben specializes in the system that uses compressible media. (3) Cal does not specialize in electrical. (4) Dee's specialty requires no fluid or gas. Which system does Cal specialize in?

Accepted Answer

Hydraulic

Answer

From clue 2, Ben = pneumatic (compressible media = compressed air/gas). From clue 4, Dee uses no fluid or gas, so Dee = mechanical. From clue 1, Ava does not work on fluid-based systems — hydraulic uses fluid, so Ava ≠ hydraulic. Since Ben = pneumatic and Dee = mechanical, Ava must be electrical or hydraulic. Since Ava ≠ hydraulic, Ava = electrical. By elimination, Cal = hydraulic. Clue 3 (Cal ≠ electrical) is consistent as a confirming constraint.

Question 5

A pump that normally runs at 1,750 RPM is coupled to a new motor running at 1,800 RPM. The pump's flow output is measured at roughly the same rate as before. Which principle BEST explains why the flow did not increase proportionally with the speed increase?

Accepted Answer

The system back-pressure increased along the system resistance curve, partially offsetting the speed gain

Answer

Pump performance is governed by the interaction between the pump curve and the system resistance curve. As pump speed increases slightly, the operating point shifts along the system curve — if the system curve rises steeply (as in a high-resistance or throttled system), the resulting flow increase is much smaller than the RPM increase would suggest. This is the fundamental reason why affinity laws apply to the pump curve in isolation but the actual operating point is the intersection with the system curve. The other options are possible but require evidence not provided in the scenario.

Ramsay Test Practice Test

Ramsay Test Practice Test

Ramsay Test Logical Thinking & Problem Solving 6