FREE AGD Operative and Restorative Dentistry Questions and Answers

Question 1

A dentist prepares a conservative, deep Class I occlusal cavity on a mandibular molar for a composite restoration. What is the primary clinical challenge associated with the high configuration factor (C-Factor) of this preparation?

Accepted Answer

Increased polymerization shrinkage stress on the bonded interfaces.

Answer

The C-Factor is the ratio of bonded to unbonded surfaces of a restoration. A Class I preparation has a high C-Factor (typically ~5) because there are five bonded surfaces (mesial, distal, buccal, lingual, pulpal) and only one unbonded surface (occlusal). This high ratio restricts the resin's ability to flow and relieve stress during polymerization, leading to significant shrinkage stress being placed on the adhesive bonds, which can cause debonding, marginal gaps, and post-operative sensitivity.

Question 2

A patient presents with a deep carious lesion on tooth #14, approaching the pulp. After caries excavation, you decide to place a liner before the final composite restoration. Which of the following is a primary advantage of using a resin-modified glass ionomer (RMGI) for this purpose?

Accepted Answer

It provides sustained fluoride release and forms a true chemical bond to the tooth structure.

Answer

Resin-modified glass ionomers combine the best properties of glass ionomers and resins. Their key advantages as a liner or base include the sustained release of fluoride ions, which has a caries-inhibitory effect, and their ability to form an ionic (chemical) bond to the calcium in hydroxyapatite, in addition to the micromechanical bond from the resin component. This provides a superior seal and biocompatibility in deep preparations.

Question 3

When preparing a maxillary molar for a lithium disilicate ceramic onlay that will cover two cusps, which of the following preparation features is most critical for ensuring the long-term fracture resistance of the restoration?

Accepted Answer

Broad, rounded internal line angles and adequate occlusal thickness.

Answer

Ceramic materials like lithium disilicate are strong under compression but brittle and susceptible to fracture under tension. Sharp internal line angles act as stress concentration points, increasing the risk of fracture. Therefore, all internal line angles must be broadly rounded to distribute occlusal forces evenly throughout the material. Furthermore, adequate occlusal thickness (typically 1.5-2.0mm) is required to provide sufficient bulk for the material to resist functional forces.

Question 4

During the application of a total-etch (etch-and-rinse) adhesive system, what is the most significant negative consequence of aggressively air-drying the dentin after the acid-etching and rinsing step?

Accepted Answer

It causes the collapse of the exposed collagen fibril network, preventing hybrid layer formation.

Answer

In a total-etch system, phosphoric acid removes the smear layer and demineralizes the superficial dentin, exposing a network of collagen fibrils. This network must be kept hydrated and 'fluffed up' to allow the hydrophilic primer and adhesive resin to penetrate it effectively, creating the micromechanical lock known as the hybrid layer. Over-drying desiccates these fibrils, causing them to collapse into a dense mat that blocks resin infiltration, resulting in a poor seal and significantly reduced bond strength.

Question 5

Which of the following is the primary mechanism by which Silver Diamine Fluoride (SDF) arrests active carious lesions?

Accepted Answer

Forming a silver-protein conjugate that is resistant to acid and enzymatic degradation.

Answer

The primary arresting mechanism of SDF involves the silver ions. The silver is strongly antimicrobial, killing cariogenic bacteria. Furthermore, it reacts with proteins in the dentin organic matrix and bacterial debris to form a dense, dark silver-protein conjugate. This layer is highly resistant to both acid demineralization and enzymatic breakdown by bacterial collagenases, effectively halting the caries process. The fluoride component contributes to remineralization, but the silver's effect is key to the arrestment.

(AGD) Academy of General Dentistry Certification Practice Test

(AGD) Academy of General Dentistry Certification Practice Test

FREE AGD Operative and Restorative Dentistry Questions and Answers