Able Seaman (AB) Exam — Questions and Answers
Question 1: What does the term 'dead reckoning' refer to?
- Visual spotting
- Wave prediction
- Estimated position tracking (Correct answer)
- GPS plotting
Correct answer: Estimated position tracking
Dead reckoning is a method of navigation where a vessel's current position is estimated by calculating the course and distance traveled from a previously known position. It relies on speed, time, and direction, without external fixes, to approximate location.
Question 2: A seaman notices a trail of oil on the water alongside the ship. The FIRST action should be:
- Spread oil-absorbent material immediately
- Log the observation and report at watch change
- Check the engine room bilge pump status
- Notify the officer on watch immediately (Correct answer)
Correct answer: Notify the officer on watch immediately
Immediate notification to the officer on watch is the first action so the source can be identified and stopped, preventing further pollution.
Question 3: A 'Mediterranean moor' is a procedure where the vessel:
- Anchors in a circular pattern with spring lines
- Drops anchor forward and backs stern to a pier or quay (Correct answer)
- Anchors with two bower anchors off the bow
- Moors alongside using breast lines only
Correct answer: Drops anchor forward and backs stern to a pier or quay
A Mediterranean moor involves anchoring with the bower anchor and backing the stern to a berth, commonly used in ports with limited space.
Question 4: You are underway in fog and hear one prolonged blast followed by two short blasts from another vessel. What does this signal indicate?
- A vessel being towed.
- A vessel at anchor.
- A vessel restricted in her ability to maneuver. (Correct answer)
- A power-driven vessel underway, making way.
Correct answer: A vessel restricted in her ability to maneuver.
According to Rule 35 (Sound Signals in Restricted Visibility), a vessel restricted in her ability to maneuver, when carrying out her work at anchor or underway, shall sound at intervals of not more than 2 minutes one prolonged blast followed by two short blasts. This signal identifies the vessel's special status to others in low visibility.
Question 5: When navigating in a Traffic Separation Scheme (TSS), what must a vessel do when crossing a separation lane?
- Sound one prolonged blast before crossing
- Cross at a very shallow angle to minimize time in the lane
- Only cross at designated crossing points
- Cross at as nearly as practicable at right angles to the general direction of traffic flow (Correct answer)
Correct answer: Cross at as nearly as practicable at right angles to the general direction of traffic flow
Under COLREGS Rule 10, a vessel crossing a traffic lane shall do so on a heading as nearly as practicable at right angles to the general direction of traffic flow.
Question 6: Which type of hatch cover is opened by folding sections to the side or ends of the hatch?
- Rolling hatch cover
- Pontoon hatch cover
- Folding (piggyback) hatch cover (Correct answer)
- Single-pull hatch cover
Correct answer: Folding (piggyback) hatch cover
Folding or piggyback hatch covers open by folding their panels in a piggyback arrangement to one end or side of the hatch coaming.
Question 7: What is a helm order?
- Cargo list
- Steering instruction (Correct answer)
- Meal rotation
- Speed adjustment
Correct answer: Steering instruction
A helm order is a command given to the helmsman (the person steering the ship) to direct the vessel's course. These instructions specify the desired rudder angle or heading, ensuring the ship follows the intended path.
Question 8: According to Rule 5 of the Navigation Rules, which of the following is a component of maintaining a proper look-out?
- Assigning the look-out duties to an officer who is also handling communication.
- Using only visual observation from the bridge.
- Relying solely on radar to detect other vessels.
- Utilizing sight, hearing, and all available means appropriate to the conditions. (Correct answer)
Correct answer: Utilizing sight, hearing, and all available means appropriate to the conditions.
Rule 5 states that "Every vessel shall at all times maintain a proper look-out by sight and hearing as well as by all available means appropriate in the prevailing circumstances and conditions so as to make a full appraisal of the situation and of the risk of collision." This requires a multi-faceted approach, not relying on a single method.
Question 9: What structural feature is designed to prevent a ship from rolling excessively in beam seas?
- Bow thruster
- Stem bar
- Chock
- Bilge keel (Correct answer)
Correct answer: Bilge keel
Bilge keels are fins welded along the bilge (curved turn of the hull) that dampen rolling motion by increasing resistance to roll.
Question 10: Which document on board provides the specific instructions for oil spill response required under US regulations (33 CFR Part 155)?
- The Ship's Stability Booklet
- The Cargo Securing Manual
- The Safety Management System manual
- The Vessel Response Plan (VRP) (Correct answer)
Correct answer: The Vessel Response Plan (VRP)
The Vessel Response Plan (VRP) is required under 33 CFR Part 155 for vessels operating in US waters and outlines oil spill response procedures.
Question 11: What is the significance of the 'righting arm' (GZ)?
- It is the vertical distance between the keel and the center of buoyancy
- It is the length of the vessel's anchor chain deployed when at anchor
- It measures the effective thrust of the vessel's propeller
- It is the horizontal distance between G and the line of buoyant force, measuring the vessel's ability to recover from heel (Correct answer)
Correct answer: It is the horizontal distance between G and the line of buoyant force, measuring the vessel's ability to recover from heel
The righting arm (GZ) is the perpendicular distance between the center of gravity and the vertical line of buoyant force; it quantifies the vessel's ability to right itself at any given angle of heel.
Question 12: What is 'worming' a rope?
- Unraveling the strands to inspect for damage
- Filling the grooves between strands with small stuff (Correct answer)
- Removing kinks from a line
- Treating rope with preservative
Correct answer: Filling the grooves between strands with small stuff
Worming fills the valleys between strands with small cordage to create a smooth, round surface before parceling and serving.
Question 13: What is the function of a bitt?
- Secure lines (Correct answer)
- Measure distance
- Pump water
- Anchor control
Correct answer: Secure lines
Bitts are strong, vertical posts or pairs of posts found on the deck of a vessel. Their primary function is to provide a robust point for securing mooring lines, towing lines, or other ropes, ensuring they are firmly held in place.
Question 14: Which class of fire involves flammable liquids such as fuel oil and paint?
- Class C
- Class D
- Class A
- Class B (Correct answer)
Correct answer: Class B
Class B fires involve flammable liquids such as oil, fuel, and paint.
Question 15: How should a seaman safely handle a wire rope with a 'meat hook' (broken strand protruding)?
- Grip it firmly and proceed normally
- Discard the wire immediately without touching it
- Tape over the protruding strand with electrical tape
- Use heavy leather gloves and handle the wire with the hook pointing away (Correct answer)
Correct answer: Use heavy leather gloves and handle the wire with the hook pointing away
Heavy leather gloves and careful handling with the protruding strand directed away prevent serious lacerations from broken wire strands.
Question 16: What is the approximate wind speed range for Beaufort Force 6?
- 34–40 knots
- 8–12 knots
- 47–54 knots
- 22–27 knots (Correct answer)
Correct answer: 22–27 knots
Beaufort Force 6, called a 'strong breeze,' corresponds to winds of 22–27 knots with large waves beginning to form.
Question 17: A fire has broken out involving pooled diesel fuel on the deck. Which class of fire is this, and what is the MOST appropriate portable extinguishing agent to use?
- Class C; Carbon Dioxide (CO2)
- Class B; Foam or Dry Chemical (Correct answer)
- Class A; Water
- Class K; Wet Chemical
Correct answer: Class B; Foam or Dry Chemical
Fires involving flammable liquids like diesel fuel are classified as Class B fires. The most appropriate extinguishing agents are foam, which smothers the fire by cutting off oxygen, or dry chemical powder, which interrupts the chemical reaction. Water should not be used as it can spread the burning fuel. CO2 is less effective in open areas, and Wet Chemical is for cooking oils (Class K).
Question 18: Under MARPOL Annex II, noxious liquid substances (NLS) are categorized to determine:
- The insurance premium for the voyage
- The type of prewash and discharge procedures required (Correct answer)
- Which crew members may handle them
- Their market value at port
Correct answer: The type of prewash and discharge procedures required
NLS categories (X, Y, Z) under MARPOL Annex II determine the prewash requirements and discharge procedures before tank cleaning effluent can be released.
Question 19: You are on a power-driven vessel underway at night and observe the lights of another vessel off your port bow. You see a green sidelight and a white masthead light. The aspect of these lights does not change over time. Which of the following is TRUE?
- You are the stand-on vessel and should maintain course and speed.
- The other vessel is the stand-on vessel, and you must give way. (Correct answer)
- You are in a head-on situation and should alter course to starboard.
- The other vessel is being overtaken and should maintain its course and speed.
Correct answer: The other vessel is the stand-on vessel, and you must give way.
This is a classic crossing situation under Rule 15. The vessel that has the other on her own starboard side is the give-way vessel. Since you see the other vessel's green light off your port side, you are the give-way vessel and are required to take early and substantial action to keep well clear, which usually involves altering course to starboard to pass astern of the other vessel. The other vessel is the stand-on vessel and is required by Rule 17 to maintain her course and speed.
Question 20: A 'permit to work' system is primarily designed to:
- Schedule routine maintenance
- Assign overtime compensation
- Record cargo loading operations
- Ensure hazardous tasks are formally authorized and controlled (Correct answer)
Correct answer: Ensure hazardous tasks are formally authorized and controlled
A permit to work system formally authorizes hazardous tasks and ensures all safety precautions are in place before work begins.
Question 21: Which part of a line is referred to as the 'standing part'?
- The final tuck of the line that secures the knot
- The loop or curve formed in the line
- The main part of the line not involved in forming the knot (Correct answer)
- The free end used to form the knot
Correct answer: The main part of the line not involved in forming the knot
The 'standing part' is the principal or main part of a line, which is not the end being used to form a knot, hitch, or bend. The other main parts are the 'bitter end' (the free end) and the 'bight' (a curve or loop in the line).
Question 22: A fire hose nozzle set to a fog pattern is most useful for:
- Protecting firefighters from radiant heat (Correct answer)
- Penetrating deep into cargo stacks
- Reaching fires at long range
- Extinguishing Class D metal fires
Correct answer: Protecting firefighters from radiant heat
A fog or spray pattern creates a water curtain that absorbs radiant heat, protecting personnel advancing toward a fire.
Question 23: What is 'backdraft' in firefighting terminology?
- Air rushing into a fire from ventilation openings
- Smoke being pushed back down a ventilation duct
- A sudden explosive ignition when oxygen is introduced to a smoldering, oxygen-depleted fire (Correct answer)
- The backflow of water through a fire hose
Correct answer: A sudden explosive ignition when oxygen is introduced to a smoldering, oxygen-depleted fire
Backdraft occurs when a smoldering fire in an oxygen-starved space suddenly receives fresh air, causing rapid ignition or explosion.
Question 24: While working on deck, a shipmate collapses and is not breathing. You are the first to respond. After ensuring the scene is safe, what is your immediate next action?
- Run to find the ship's medical officer.
- Roll the person into the recovery position.
- Start chest compressions immediately.
- Call for help and check for a pulse. (Correct answer)
Correct answer: Call for help and check for a pulse.
In any first aid scenario, the first step after ensuring your own safety is to assess the victim and summon assistance. You should loudly call for help to alert others who can assist and bring necessary medical equipment, while simultaneously checking for vital signs like a pulse to determine the next course of action (e.g., starting CPR).
Question 25: A 'veering' wind shifts in which direction?
- Toward the south only
- Toward the north only
- Clockwise (e.g., S to W) (Correct answer)
- Counterclockwise (e.g., S to E)
Correct answer: Clockwise (e.g., S to W)
A veering wind shifts clockwise in direction (e.g., from south to west) and in the Northern Hemisphere often signals improving weather.
Question 26: In the Northern Hemisphere, winds circulate around a high-pressure system in which direction?
- Outward from the center in all directions
- Inward toward the center
- Counterclockwise
- Clockwise (Correct answer)
Correct answer: Clockwise
In the Northern Hemisphere, winds circulate clockwise around high-pressure (anticyclonic) systems due to the Coriolis effect.
Question 27: Nylon rope is preferred for anchor rodes and tow lines primarily because of its:
- Low stretch that maintains tension
- High elasticity that absorbs shock loads (Correct answer)
- Resistance to UV degradation
- Ability to float on the surface
Correct answer: High elasticity that absorbs shock loads
Nylon stretches significantly under load, acting as a shock absorber that reduces peak stress on deck fittings and anchors.
Question 28: Which of the following day shapes should a vessel engaged in fishing, but not trawling, exhibit?
- A diamond shape.
- One black ball.
- A cylinder.
- Two cones with their apexes together in a vertical line. (Correct answer)
Correct answer: Two cones with their apexes together in a vertical line.
Rule 26 specifies that a vessel engaged in fishing, other than trawling, shall exhibit by day a shape consisting of two cones with their apexes together in a vertical line. This shape indicates its activity to other vessels during daylight hours.
Question 29: When working aloft or over the side, which safety item is MOST important to wear in addition to a life jacket?
- Steel-toed boots
- A hard hat only
- Heavy-duty gloves
- A safety harness with a lanyard (Correct answer)
Correct answer: A safety harness with a lanyard
A safety harness with a lanyard is essential when working aloft or over the side to prevent falls.
Question 30: What is the 'camber' of a ship's deck?
- The transverse curvature of the deck, higher at the centerline than at the sides (Correct answer)
- The overhang of the bow beyond the waterline
- The vertical distance between decks
- The fore-and-aft slope of the keel
Correct answer: The transverse curvature of the deck, higher at the centerline than at the sides
Camber (or round of beam) is the athwartship curvature of a deck, sloping from the centerline down to the sides to aid water drainage.
Question 31: What does a thermal imaging camera (TIC) allow firefighters to do aboard a ship?
- Detect hidden heat sources and hot spots through smoke (Correct answer)
- Identify the type of combustible material burning
- Communicate with the bridge during emergencies
- Measure oxygen levels in a compartment
Correct answer: Detect hidden heat sources and hot spots through smoke
A TIC detects infrared radiation and displays heat signatures, allowing firefighters to locate victims or hot spots through dense smoke.
Question 32: A power-driven vessel is towing another vessel astern. The length of the tow, from the stern of the towing vessel to the after end of the tow, is greater than 200 meters. What day shape must the towing vessel display?
- Two cones, apexes together.
- A diamond shape. (Correct answer)
- A black ball.
- A cylinder.
Correct answer: A diamond shape.
According to Rule 24(a)(v), a power-driven vessel when towing, if the length of the tow exceeds 200 meters, shall exhibit a diamond shape where it can best be seen.
Question 33: You are on a power-driven vessel and see a sailing vessel on your starboard bow on a collision course. According to the hierarchy of responsibilities between vessels (Rule 18), which vessel is the stand-on vessel?
- Whichever vessel is larger.
- The power-driven vessel because it is more maneuverable.
- The sailing vessel. (Correct answer)
- Both vessels are give-way and must take action.
Correct answer: The sailing vessel.
Rule 18 establishes a hierarchy of responsibility. A power-driven vessel underway shall keep out of the way of a sailing vessel, unless the sailing vessel is overtaking the power-driven vessel. Therefore, the sailing vessel is the stand-on vessel and should maintain its course and speed.
Question 34: What is the purpose of the 'Plimsoll mark' (load line mark) on a vessel's hull?
- To show the height of the propeller below the waterline
- To mark the vessel's midship point for stability calculations
- To indicate the vessel's registered tonnage
- To indicate the maximum safe loading depth in various conditions and water types (Correct answer)
Correct answer: To indicate the maximum safe loading depth in various conditions and water types
The Plimsoll mark indicates the maximum draft (deepest safe loading level) for a vessel in different seasons and water densities.
Question 35: What action should an AB take immediately upon discovering a fire on board?
- Report to the bridge and wait for orders
- Sound the alarm, then fight the fire if safe to do so (Correct answer)
- Abandon ship immediately
- Attempt to extinguish it before raising the alarm
Correct answer: Sound the alarm, then fight the fire if safe to do so
The first priority is to sound the alarm to alert the crew, then attempt to fight the fire if it is safe to do so.
Question 36: What does the sound signal of five short blasts mean?
- All clear
- Danger signal (Correct answer)
- Slow down
- Turn to port
Correct answer: Danger signal
According to COLREGs Rule 34(d), five short and rapid blasts on the whistle is the international danger signal. This signal is used when a vessel is in doubt about the intentions or actions of another vessel, or whether sufficient action is being taken to avoid collision. It alerts other vessels to a potential hazardous situation.
Question 37: Which type of cargo requires the most ventilation during stowage to prevent moisture damage?
- Liquid bulk in tanks
- Refrigerated containers
- Steel coils
- Hygroscopic dry cargo such as grain or coffee (Correct answer)
Correct answer: Hygroscopic dry cargo such as grain or coffee
Hygroscopic cargo absorbs moisture from the air, so adequate ventilation is critical to prevent condensation and cargo sweat damage.
Question 38: The 'sheer' of a vessel refers to:
- The angle of the mast from vertical
- The outward flare of the bow
- The upward curve of the deck from amidships toward the bow and stern (Correct answer)
- The slope of the keel from bow to stern
Correct answer: The upward curve of the deck from amidships toward the bow and stern
Sheer is the longitudinal curvature of the main deck, rising toward the bow and stern from the lowest point amidships.
Question 39: What does a lookout do?
- Observe surroundings (Correct answer)
- Clean decks
- Manage engines
- Inspect cargo
Correct answer: Observe surroundings
A lookout's primary duty is to maintain a continuous and vigilant watch by sight and hearing for other vessels, navigational hazards, and any changes in the environment. This is essential for preventing collisions and ensuring the safety of the vessel.
Question 40: A vessel is loaded with heavy cargo concentrated in the midship holds, while the fore and aft holds are empty. If wave crests are supporting the bow and stern, what type of longitudinal stress is the hull experiencing?
- Hogging
- Pounding
- Sagging (Correct answer)
- Racking
Correct answer: Sagging
Sagging is the stress condition where the middle of the ship's hull bends downwards. This occurs when there is excessive weight in the center of the vessel and buoyancy is concentrated at the ends, such as when the ship is in the trough between two waves or loaded heavily amidships.
Question 41: When should a wire rope be condemned and replaced?
- When it becomes wet
- When it shows any surface rust
- After any single use at maximum rated load
- When it has more than the allowable number of broken wires per lay length (Correct answer)
Correct answer: When it has more than the allowable number of broken wires per lay length
Wire rope is typically condemned when the number of broken wires in one lay length exceeds the allowable limit specified by OSHA or the manufacturer.
Question 42: What effect does adding weight to a vessel have on its draft?
- Draft is unaffected by added weight
- It increases draft as the vessel sinks deeper (Correct answer)
- It causes the vessel to trim by the head only
- It decreases draft as buoyancy adjusts
Correct answer: It increases draft as the vessel sinks deeper
Adding weight increases the vessel's displacement, causing it to sink deeper until the additional buoyant force equals the added weight.
Question 43: What is the maximum number of persons a 20-person capacity liferaft is required to hold in an emergency?
- 25
- 20 (Correct answer)
- 18
- 24
Correct answer: 20
A liferaft is certified for a specific number of persons and must not exceed that rated capacity.
Question 44: A 'long splice' is used primarily because it:
- Is faster to make than a short splice
- Requires no special tools
- Can be undone quickly
- Maintains nearly the original diameter of the rope (Correct answer)
Correct answer: Maintains nearly the original diameter of the rope
A long splice tapers the strands so the finished splice is almost the same diameter as the original rope, allowing it to pass through blocks.
Question 45: When coiling a right-laid rope, the correct direction to coil is:
- Clockwise (with the lay) (Correct answer)
- Figure-eight only
- Either direction equally
- Counter-clockwise (against the lay)
Correct answer: Clockwise (with the lay)
Right-laid rope should be coiled clockwise to follow the lay of the strands and prevent kinking.
Question 46: Which of the following items is a required component of a SOLAS-compliant Fireman's Outfit?
- A multi-gas detector.
- A handheld GPS unit.
- A thermal imaging camera.
- An intrinsically safe (explosion-proof) safety lamp. (Correct answer)
Correct answer: An intrinsically safe (explosion-proof) safety lamp.
A SOLAS-compliant Fireman's Outfit must include specific personal equipment. Among the required items are an electric safety lamp (hand lantern) of an approved, intrinsically safe or explosion-proof type, with a minimum burning period of three hours. While other listed items are useful, they are not part of the minimum required equipment for the outfit itself under SOLAS.
Question 47: While mooring, you are instructed to 'flemish down' the excess line on deck. What are you being asked to do?
- Throw the end of the line overboard
- Secure the line to a bitt with extra turns
- Coil the line into a neat, flat spiral on the deck (Correct answer)
- Fake the line in long, flat bights
Correct answer: Coil the line into a neat, flat spiral on the deck
Flemishing a line involves arranging it into a tight, flat spiral coil on the deck. This is done for neatness and to keep the decks clear, especially when a vessel is alongside for a short period.
Question 48: The 'bitter end' of a line refers to:
- The working end used to tie knots
- The frayed end of an old rope
- The free end thrown ashore
- The inboard end secured to the vessel (Correct answer)
Correct answer: The inboard end secured to the vessel
The bitter end is the last and inboard end of a rope or chain, secured to the ship's structure.
Question 49: What is a nautical mile?
- 1.5 miles
- 1.1508 miles (Correct answer)
- 1 mile
- 0.5 kilometers
Correct answer: 1.1508 miles
A nautical mile is a unit of distance used in marine and aviation navigation, defined as one minute of arc of a great circle. It is approximately 1.1508 statute miles (or 1,852 meters), making it a standard measure for distances at sea.
Question 50: When is a vessel considered 'restricted in her ability to maneuver'?
- Due to operational limitations (Correct answer)
- When fast-moving
- In open water
- During fishing
Correct answer: Due to operational limitations
A vessel is considered 'restricted in her ability to maneuver' when, due to the nature of her work, she is unable to deviate from her course or keep out of the way of other vessels as required by COLREGs. This includes operations such as dredging, cable-laying, surveying, or launching/recovering aircraft, where the vessel's movement is constrained by its specific task.
Question 51: A CO2 fixed fire-extinguishing system is MOST effective in which space?
- Open deck areas
- Enclosed machinery spaces (Correct answer)
- Crew accommodation quarters
- Cargo holds with live animals
Correct answer: Enclosed machinery spaces
CO2 systems are most effective in enclosed machinery spaces where the gas can blanket the fire and displace oxygen.
Question 52: Under the International Rules, what is the whistle signal for a power-driven vessel altering its course to port when in sight of another vessel?
- Three short blasts.
- One short blast.
- Two short blasts. (Correct answer)
- One prolonged blast.
Correct answer: Two short blasts.
Rule 34(a) of the COLREGs specifies that two short blasts on the whistle indicate "I am altering my course to port." One short blast means altering course to starboard, and three short blasts mean operating astern propulsion.
Able Seaman (AB) Exam
The Able Seaman (AB) exam certifies mariners to perform duties as an Able Seaman on various vessels, demonstrating knowledge of seamanship, safety, and navigation.
Exam Rules
- You can skip questions and return to them later
- Flag questions for review before submitting
- No feedback shown until you submit the entire exam
- Unanswered questions count as wrong — answer everything
- 10 pretest questions are mixed in and don't affect your score
- Timer auto-submits when time runs out
- Your progress is auto-saved every 30 seconds
Practice questions written with AI assistance and published by Nathan Beja, founder of Practice Test Geeks. They are not real exam questions. Exam facts are checked against the official sources linked below. Editorial policy
Sources & references
Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy
- dco.uscg.mil — Test delivery, passing score · verified Nov 2026
- ecfr.gov — Score validity, retake policy, renewal · verified Oct 2026