CDL Practice Test: Video 4 Answers (25 Questions) Flashcards
25 cards from real CDL practice questions. Tap to flip, then mark Knew It or Still Learning — missed cards come back until you master them.
Read the first 20 CDL Practice Test: Video 4 Answers (25 Questions) flashcards as text
Where is compressed air stored?
Answer: Main reservoirs
Compressed air, generated by the air compressor, is stored in large metal tanks called main reservoirs or air tanks. These tanks hold a reserve of compressed air, which is then supplied to the brake chambers and other air-operated accessories. Having these reservoirs ensures a constant supply of air pressure for braking, even if the compressor is not actively pumping.
At what air pressure must the low air pressure warning signal come on?
Answer: 60 psi
Federal regulations mandate that the low air pressure warning signal must activate when the air pressure in the service air tanks falls below 60 psi (or half the governor cut-out pressure on older vehicles). This warning alerts the driver to a critical loss of air pressure, indicating a potential problem with the air brake system that requires immediate attention.
What is the alcohol evaporator's primary purpose?
Answer: Put alcohol into the air system
An alcohol evaporator, found in some older air brake systems, is designed to inject alcohol vapor into the air lines. This alcohol helps prevent moisture in the air system from freezing during cold weather, which could otherwise cause brake components to malfunction and lead to brake failure.
What is the typical air pressure of a fully charged air brake system?
Answer: 125 psi
125 psi. A fully charged air system typically has 125 psi of air pressure.
Which of the following devices can be used as the low air pressure warning signal?
Answer: Any of the above
Federal regulations require commercial vehicles with air brakes to have a low air pressure warning signal to alert the driver when system pressure drops below 60 psi. This critical warning can be provided by various means, including an audible buzzer, a visual red warning light, or a mechanical arm known as a 'wig-wag.' All these devices serve the same essential safety function.
Containment rules are rules that _______.
Answer: All of the listed answers.
Containment rules are a comprehensive set of regulations designed to ensure the safe handling of hazardous materials throughout their transportation journey. These rules provide detailed instructions for drivers on how to properly load, transport, and unload hazardous materials. Adhering to these guidelines is crucial to prevent spills, leaks, and exposure, thereby protecting public safety and the environment.
The shippers must ________.
Answer: All of the listed answers.
Shippers of hazardous materials have a comprehensive set of responsibilities to ensure the safe transportation of these dangerous goods. This includes properly packaging the materials in approved containers, accurately marking packages with necessary information, and correctly labeling them with hazard warnings. These actions are critical for compliance, safety, and informing handlers and emergency responders.
What is one of first things you should do before unloading a hazardous material?
Answer: Set the parking brake.
Before beginning any unloading operation, especially with hazardous materials, safety is paramount. Setting the parking brake is one of the first and most crucial steps to ensure the vehicle remains stationary and secure. This prevents accidental movement that could lead to spills, injuries, or other dangerous situations during the unloading process.
Shippers put a hazard warning label on all packages of hazardous materials. On most packages the hazard warning label is what shape?
Answer: Diamond.
Hazard warning labels on packages of hazardous materials are specifically designed in a diamond shape. This distinctive shape makes them easily recognizable and immediately signals the presence of dangerous goods to handlers, emergency responders, and drivers. The diamond shape is a standardized feature mandated by regulations to ensure clear and consistent identification of hazardous materials during transportation.
If you are driving ____mph above the posted speed limit, you are considered to be speeding excessively.
Answer: 15 mph.
Excessive speeding is a serious offense for commercial drivers, leading to significant penalties and increased accident risk. Driving 15 mph or more above the posted speed limit is generally considered excessive speeding. This threshold is important for CDL holders to be aware of, as it can result in fines, points on their license, and potential disqualification from operating a commercial motor vehicle.
Which of the following is a necessary step to test your service brakes?
Answer: All of the listed answers.
To properly test service brakes, several steps are necessary to ensure safety and functionality. These include waiting for normal air pressure, releasing the parking brake, and then moving the vehicle forward slowly (typically 5 mph) before applying the foot brake firmly. This allows the driver to check for proper braking action, straight stopping, and any unusual pulling.
The air pressure governor cut-out is typically within what psi range?
Answer: 120-140 psi.
The air pressure governor in an air brake system controls when the air compressor starts and stops. The cut-out pressure is the point at which the compressor stops pumping air into the tanks, typically set between 120-140 psi. This range ensures sufficient air pressure for safe braking while preventing over-pressurization of the system.
You are testing your trailer's emergency brakes. First you should _____.
Answer: Charge the trailer air brake system.
Before testing a trailer's emergency brakes, it is essential to first charge the trailer air brake system. This means connecting the air lines from the tractor to the trailer and allowing the trailer's air tanks to fill to normal operating pressure. Once the system is charged, the emergency brakes can be properly tested by applying and releasing the trailer air supply control.
Knowing how to couple and uncouple correctly is ________.
Answer: Important for the safe operation of combination vehicles.
Correctly coupling and uncoupling a combination vehicle is a fundamental skill for CDL drivers. Improper procedures can lead to serious accidents, such as the trailer detaching from the tractor, loss of air brakes, or damage to equipment. Therefore, mastering these procedures is crucial for ensuring the safety of the driver, the vehicle, and other road users.
All versions of the Class A Pre-trip inspection test will include _______.
Answer: All of the listed answers.
All versions of the Class A Pre-trip Inspection test are designed to assess a driver's ability to thoroughly inspect a combination vehicle for safe operation. This includes a detailed in-cab inspection of controls and gauges, an engine start to check vital systems, and a comprehensive inspection of the coupling system to ensure the tractor and trailer are securely connected. These elements are fundamental to safe driving.
Where should you lead students if the bus is on fire?
Answer: Upwind of the bus.
If a bus is on fire, students should be led upwind of the bus. This means moving them to a location where the wind will carry smoke and flames away from them. Staying upwind helps protect students from inhaling toxic fumes and being exposed to the heat of the fire, ensuring their safety during an evacuation and preventing further harm.
Passive crossings typically have?
Answer: Yellow circular advance warning signs.
Passive railroad-highway crossings are typically identified by yellow circular advance warning signs. These signs alert drivers to the presence of a railroad crossing ahead, even though there may not be active warning devices like flashing lights or gates. The yellow circular sign serves as a crucial visual cue for drivers to exercise caution, slow down, and prepare to stop and look for trains.
At a passive railroad-highway crossing, you need to ____.
Answer: All of the listed answers.
At a passive railroad-highway crossing, which lacks active warning devices like gates or flashing lights, the driver must take full responsibility for safety. This involves recognizing the crossing, actively searching for any trains using the tracks, and deciding if there is sufficient clear space to cross safely without stopping on the tracks. All these steps are critical to prevent collisions at unguarded crossings.
Because students may drop an object near the bus during loading and unloading, you should _______.
Answer: Watch carefully as they enter and exit the bus.
The area around a school bus during loading and unloading is a high-risk zone for students. Because students might drop objects and bend down to retrieve them, or move unpredictably, it is crucial for the driver to watch them carefully as they enter and exit the bus. This constant vigilance helps prevent accidents, ensuring students remain visible and safe from the bus's wheels or other traffic.
When should you turn on your right turn signal indicator before pulling over?
Answer: 100-300 ft.
Activating your turn signal 100-300 feet before pulling over provides ample warning to other drivers and pedestrians of your intentions. This allows them sufficient time to react and adjust their speed or position, preventing sudden maneuvers and reducing the risk of collisions. This is especially important for large vehicles like buses, which require more space and time to maneuver.
Written and edited by Nathan Beja, founder of Practice Test Geeks, with AI assistance. Exam facts are checked against the official sources linked below. Editorial policy
Sources & references
Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy