← All ARRT Flashcard Decks

Equipment Operation and QA Flashcards

6 cards from real ARRT practice questions. Tap to flip, then mark Knew It or Still Learning — missed cards come back until you master them.

Read the first 6 Equipment Operation and QA flashcards as text
  1. A radiograph of the pelvis exhibits a uniform loss of density across the entire image. The technologist used a focused grid and suspects grid cutoff. Which of the following errors is the MOST likely cause?

    Answer: Off-level grid error

    An off-level grid error, where the X-ray beam is angled across the lead strips or the grid is tilted, results in the absorption of the primary beam across the entire surface of the grid. This causes a uniform decrease in radiographic density or a light, underexposed image. An upside-down focused grid would cause severe cutoff on the lateral edges but not in the center. Off-center and off-focus errors also result in a non-uniform density loss, typically more pronounced on one side or toward the edges.

  2. A quality control test is performed on a single-phase, full-wave rectified x-ray unit. A spinning top test is used to evaluate timer accuracy with an exposure time of 0.1 seconds. How many dots should appear on the finished radiograph?

    Answer: 12

    For a single-phase, full-wave rectified generator, there are 120 pulses of x-ray production per second (2 pulses per cycle x 60 Hz). To find the expected number of dots, multiply the pulses per second by the exposure time: 120 pulses/second * 0.1 seconds = 12 dots. A half-wave rectified unit would produce 6 dots, and other values would indicate a different rectification or timer malfunction.

  3. Which of the following describes the primary function of a falling load generator?

    Answer: To use the maximum heat capacity of the tube to achieve the shortest possible exposure time.

    A falling load generator starts the exposure with the highest possible mA and then drops the mA to lower levels as the tube's heat loading capacity is reached. This process is designed to deliver the desired mAs in the shortest time possible, which is crucial for minimizing motion artifacts.

  4. A digital radiograph of a knee appears grainy and mottled. The technologist confirms that positioning and collimation were accurate. Which of the following is the MOST likely cause of this appearance and how should it be corrected?

    Answer: Quantum mottle; increase the mAs.

    A grainy or mottled appearance on a digital image, often described as quantum mottle or noise, is typically caused by an insufficient number of photons reaching the image receptor (underexposure). The primary way to correct for this is to increase the quantity of photons, which is achieved by increasing the mAs. Grid cutoff would likely present as a more uniform or localized loss of density, not a grainy texture throughout the image. Saturation is an effect of overexposure, and processor artifacts are less common in digital radiography.

  5. Which of the following is a key component of the NEMA XR-29 (MITA Smart Dose) standard for CT scanners?

    Answer: Automatic Exposure Control (AEC).

    The NEMA XR-29 standard, also known as MITA Smart Dose, includes four key features to help manage radiation dose in CT. These are: Automatic Exposure Control (AEC), DICOM Radiation Dose Structured Reporting, CT Dose Check features, and reference adult and pediatric protocols. While iterative reconstruction is a dose-saving technology, it is not a required component of the XR-29 standard itself.

  6. During routine quality control for an Automatic Exposure Control (AEC) system, the technologist makes several exposures of a phantom at different mA stations while keeping all other factors constant. The goal of this test is to evaluate the AEC's:

    Answer: Exposure reproducibility.

    This procedure describes a test for exposure reproducibility or reciprocity. The AEC should be able to adjust the exposure time to produce a consistent image receptor exposure (and thus, image density/brightness) regardless of the mA station selected. The mAs should remain constant. Testing the kVp response would involve changing the kVp, and testing the density controls would involve adjusting the +/– density settings.

Written and edited by , founder of Practice Test Geeks, with AI assistance. Exam facts are checked against the official sources linked below. Editorial policy

Sources & references

Exam facts on this page (fees, format, dates, passing scores) are checked against these official sources; the date is our last check. Editorial policy

  1. arrt.org — Registration deadline, test dates, score release, retake policy, passing score, eligibility, fees, renewal, retake fee, exam information · verified Nov 2026
  2. pearsonvue.com — Test delivery · verified Nov 2026
  3. assets-us-01.kc-usercontent.com — Exam format, time limit · verified Nov 2026